HP 8000 - Elite Convertible Minitower PC Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 114

background image

Technical Reference Guide

www.hp.com

5-9

Input/Output Interfaces

5.6 Universal Serial Bus Interface

The Universal Serial Bus (USB) interface provides asynchronous/isochronous data transfers with
compatible peripherals such as keyboards, printers, or modems. This high-speed interface
supports hot-plugging of compatible devices, making possible system configuration changes
without powering down or even rebooting systems.

These systems provide ten externally-accessible USB ports; four front panel USB ports (which
may be disabled) and six USB ports on the rear panel. In addition, the SFF and CMT form factors
support a media reader accessory that uses two USB ports through a system board header
connection. The USB ports are dynamically configured to either a USB 1.1 controller or the USB
2.0 controller depending on the capability of the peripheral device. The 1.1 controllers provide a
maximum transfer rate of 12 Mb/s while the 2.0 controller provides a maximum transfer rate of
480 Mb/s. Table 5-5 shows the mapping of the USB ports.

USB

5.6.1 USB Connector

These systems provide type-A USB ports as shown in Figure 5-7.

Figure 5-7. Universal Serial Bus Connector (as viewed from rear of chassis)

Table 5-5.

ICH10 USB Port Mapping

ICH10

Controller

Signals

USB Connector Location (all form factors

USB 1.1 #1,
USB 2.0 #1

Data 0P, 0N

System board header P150

Data 1P, 1N

System board header P150

USB 1.1 #2
USB 2.0 #1

Data 2P, 2N

Front panel

Data 3P, 3N

Front panel

USB 1.1 #3
USB 2.0 #1

Data 4P, 4N

Front panel

Data 5P, 5N

Front panel

USB 1.1 #4
USB 2.0 #2

Data 6P, 6N

Rear panel, quad

Data 7P, 7N

Rear panel, quad

USB 1.1 #5
USB 2.0 #2

Data 8P, 8N

Rear panel, quad

Data 9P, 9N

Rear panel, quad

USB 1.1 #6
USB 2.0 #2

Data 10P, 10N

Rear panel, dual

Data 11P, 11N

Rear panel, dual

1

2

3

4

«
...
57
58
59
60
61
...
»

Содержание 8000 - Elite Convertible Minitower PC



















































































































Отзывы:

Нет отзывов

Похожие инструкции для 8000 - Elite Convertible Minitower PC

Бренд: IBM Страницы: 136

Бренд: IBM Страницы: 202

ThinkPad G40 Series

Бренд: IBM Страницы: 160

Бренд: Chen Hsong Страницы: 124

Бренд: Gateway Страницы: 52

Бренд: AOpen Страницы: 20

Бренд: Vivo Страницы: 16

Бренд: Lenovo Страницы: 18

Бренд: Lenovo Страницы: 4

Бренд: Lenovo Страницы: 4

Бренд: Lenovo Страницы: 2

90BX E50-00 Series

Бренд: Lenovo Страницы: 49

Бренд: Lenovo Страницы: 82

892204U - C200 8922 - Celeron M 1.6 GHz

Бренд: Lenovo Страницы: 56

90B6 [H50-50 ES]

Бренд: Lenovo Страницы: 63

821532U - ThinkCentre M52 - 8215

Бренд: Lenovo Страницы: 530

Бренд: Lenovo Страницы: 72

Бренд: Lenovo Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды