HP 333A Скачать руководство пользователя страница 28

Страница: 28 / 53

TM11-6625-1576-15

Section v
Paragraphs 5-13 to 5-16 and Table 5-4

Model 333A/334A

j. The Electronic Counter shall indicate the period

of 5 cps -3%, i. e. 194 to 200 msec.

k. Repeat steps b through h with controls set as

indicated in Table 5-4. The Electronic Counter shall
indicate the Test Oscillator output frequencies within
the limits indicated.

5-13. INPUT RESISTANCE CHECK

a. Connect Test Oscillator (-hp- Model 651A) 600

Ω

output to Distortion Analyzer INPUT terminals.

b. Set Distortion Analyzer controls as follows:

FUNCTION Selector . . . . . . VOLTMETER
SENSITIVITY Selector . . . . . . . . . MAX.
SENSITIVITY VERNIER Control . . . . . MIN.

METER RANGE Selector. . . . . . . 1 VOLT

c. Set Test Oscillator controls as follows:

FREQUENCY RANGE . . . . . . . . . . X10
FREQUENCY Dial . . . . . . . . . . . . . 10

OUTPUT ATTENUATOR . . . . . . 1.0 VOLT

d. Adjust Test Oscillator AMPLITUDE control for

an indication of 1.0 volt (E

) rms on the Distortion

Analyzer meter.

e. Connect a 100 K

Ω

) ±1. 0%, 1/2 watt, fixed

carbon film resistor in series with the Distortion

Analyzer INPUT. Note the Distortion Analyzer meter

reading (E

f. Calculate the Distortion Analyzer input resis-

tance using the following formula:

g. The input resistance shall be 1 M

Ω

±5%.

h. Switch FUNCTION selector to Distortion and

calculate the input resistance in this position. It shall
be 1 M

Ω ±5%.

5-14.

INPUT SHUNT CAPACITANCE CHECK.

Set Distortion Analyzer controls as follows:

FUNCTION Selector . . . . . . . VOLTMETER

METER RANGE Selector . . . . . . . 1 VOLT

Connect an L - C meter to the 333A/334A and

measure the input capacitance.

c. The L - C meter shall indicate less than 30 pf.

d. Switch the Distortion Analyzer on the 0. 3 range

and measure capacitance. Meter shall indicate less
than 60 pf.

5-4

e. Set Distortion Analyzer controls as follows:

FUNCTION Selector . . . . . .DISTORTION
SENSITIVITY Selector . . . . . . . . . . MIN.

METER RANGE Selector . . . . . . . VOLTS

f. Measure Capacitance at each SENSITIVITY

selector setting of the Distortion Analyzer. The L - C
meter shall indicate less than 60 pf on each of these
settings.

5-15. MINIMUM INPUT LEVEL CHECK.

a. Connect Test Oscillator (-hp- Model 651A) 600

Ω

output to Distortion Analyzer INPUT terminals l

Terminate test oscillator with

600

Ω

±1% 1/2 w resistor.

Set Distortion Analyzer controls as follows:

FUNCTION Selector . . . . . . . VOLTMETER

METER RANGE Selector . . . . . . .3 VOLT
SENSITIVITY Selector . . . . . . . . . MIN.
SENSITIVITY VERNIER . . . . . . . . , CCW

Set Test Oscillator for 20 cps.

Adjust Test Oscillator amplitude for a Distortion

Analyzer

meter indication O. 3 volts.

e. Switch Distortion Analyzer FUNCTION selector

to SET LEVEL.

f. Switch SENSITIVITY selector to MAX and

VERNIER to full CW. The SENSITIVITY controls shall
have sufficient range to give a full scale meter reading.

5-16.

DC ISOLATION CHECK.

Connect 333A/334A as shown in Figure 5-4.

REMOVE SHORTING BARS BETWEEN
POWER LINE GROUND TERMINALS ON
DISTORTION ANALYZER INPUT TERMI-
NALS AND FUNCTION GENERATOR OUT-
PUT TERMINALS.

Set Distortion Analyzer controls as follows:

FUNCTION Selector . . . . . .VOLTMETER

METER RANGE Selector . . . . . . . 1 VOLT

c. Apply ac power to dc power supply and set for

400 v. Set Power SuppIy controls but do not apply dc
to the Distortion Analyzer.

d. Set Function Generator for 1 Kc and adjust the

amplitude control for an indication of 0. 9 on the Dis-
tortion Analyzer meter.

Содержание 333A






















































Результаты поиска

Содержание 333A

Отзывы:

Похожие инструкции для 333A

Бренды по названию

Популярные бренды

HP 333A, Техническое руководство

Результаты поиска

Содержание 333A

Отзывы:

Похожие инструкции для 333A

Бренды по названию

Популярные бренды