HP 333A Скачать руководство пользователя страница 26

Страница: 26 / 53

TM 11-6625-1576-15

Section V
Paragraphs 5-10 to 5-11, Figure 5-2 and Table 5-2

setting. Each decrease of the RANGE
switch represents 10 db fundamental re-
jection. Therefore, the total fundamental

rejection is the sum of the Wave Analyzer

reading and the 333A/334A indication.

k. The Distortion Analyzer METER RANGE setting

plus the Wave Analyzer RANGE setting plus the two

meter indications shall total more than -80 db.

5-10. SECOND HARMONIC ACCURACY CHECK.

a. Connect Test Oscillator (-hp-Model 651A) 600

Ω

output to Distortion Analyzer *

b. Set Distortion Analyzer controls as follows:

FUNCTION Selector . . . . . . . SET LEVEL
FREQUENCY RANGE . . . . . . . . . . . X1
Frequency Dial . . . . . . . . . . . . . . .20

METER RANGE Selector . . . . . . . . . 0 DB

c. Set Test Oscillator controls (-hp- Model 651A)

as follows:

FREQUENCY RANGE . . . . . . . . . . . X10
FREQUENCY Dial. . . . . . . . . . . . . 2

OUTPUT ATTENUATOR . . . . . 1.0 VOLTS
AMPLITUDE . . . . . . . . . . . . . . l Volt

d. Adjust Distortion Analyzer SENSITIVITY con-

trols for a meter reading of O db.

e. Switch Distortion Analyzer FUNCTION selector

to DISTORTION. Adjust Frequency dial and BALANCE
controls for a null indication on meter.

f. Switch Distortion Analyzer FUNCTION selector

to SET LEVEL.

g. Adjust Test Oscillator frequency to 40 cps. Ad-

just AMPLITUDE control for a O db indication on the
Distortion Analyzer meter.

h. Switch Distortion Analyzer FUNCTION selector

to DISTORTION. The meter reading shall not change
more than ±0. 6 db.

Model 333A/334A

j. Repeat steps a through h at the frequency settings

indicated in Table 5-2. The meter readings shall

change within the limits specified.

Table 5-2. Second Harmonic Accuracy Check

5-11.

DISTORTION INTRODUCED BY INSTRUMENT
CHECK AND AUTOMATIC CONTROL LOOP
OPERATION.

Connect 333A/334A as shown in Figure 5-2.

Set Distortion Analyzer controls as follows:

FUNCTION Selector . . . . . . . SET LEVEL
SENSITIVITY Selector . Position 1 step CCW

from Full CW position

SENSITIVITY VERNIER Control . . full CCW

METER RANGE Selector . . . . . . . . . . 0 db

FREQUENCY RANGE Selector . . . . . . . Xl
Frequency Dial . . . . . . . . . . . . . . .5

Set oscillator for approximately 1 volt output at

5 cycles.

d. Set filter box for 5 cycles.

e. Adjust oscillator amplitude for an indication of

+2 db on the Distortion Analyzer meter.

f. Switch Distortion Analyzer FUNCTION selector

to DISTORTION. Adjust frequency dial and BALANCE
controls for a null meter indication. (If reading is in
lower 1/3 of meter scale, decrease METER RANGE
selector setting. )

g. The meter indication at “null” shall be at least

-8 db on the -60 db METER RANGE which is equiva-

lent to -70 db. Note reading.

Figure 5-2. Instrument Induced Distorition and Automatic Control Loop Test Setup

5 - 2

Содержание 333A






















































Результаты поиска

Содержание 333A

Отзывы:

Бренды по названию

Популярные бренды

HP 333A, Техническое руководство

Результаты поиска

Содержание 333A

Отзывы:

Бренды по названию

Популярные бренды