BASIC INSTALLATION GUIDE
BASIC INSTALLATION GUIDE
INSTALLATION HARDWARE
INSTALLATION HARDWARE
8 x 2 1/2” Pan Head Screws (per 4 ft
of bracket)
25 x 1 1/4” Pan Head Screws (per 4
ft of bracket)
4 x 3/4” Set Screws (per 4 ft of
bracket minimum)
1 x 3/16” Cobalt Drill Bit
1 x Hex Key
BITS REQUIRED
BITS REQUIRED
17/64” HSS Steel Drill Bit (Set
Screw Install)
5/16” #18 HSS H3 Tap Bit (Set
Screw Install)
Epoxy Glue (Glue Install)
TOOLS REQUIRED
TOOLS REQUIRED
Tape Measure
Electric Drill
Level
Stud Finder
(Router)
(Table Saw)
hovrsolutions.com/learn
Hovr Strong Solutions (the “Company”) makes no representation or warranty as to the suitability of its products for any particular purpose, use, or installation, nor does it make any suggestion as to the method by
which any of its products should be installed. The Company makes no suggestion nor shall be taken to provide any instruction on any tools, equipment or machinery used in any way in connection with its products,
and strongly suggests that the consumer consult with and abide by any user manuals or instructions provided by the manufacturer of any utilized tools, equipment or machinery and at any time they are used, that
such use is conducted in a safe and lawful manner. It is the responsibility of the consumer to ensure the correct usage of any tools, equipment, or machinery utilized at any time in connection with any Company
products.
The information provided in any video by the Company is not intended as, and shall not be understood or construed as, advice or instruction in the operation of any tools, equipment, or machinery for use in connection
with any Company products. Neither the Company, nor any of its employees, agents or anyone else for whom it is at law responsible shall be held liable or responsible for any loss, damage, or injury stemming from the
use of any tool, equipment, or machinery utilized by a consumer in connection with any Company products.
BASIC INSTALLATION GUIDE
BASIC INSTALLATION GUIDE
[email protected]
(844) 574-2307
WHAT YOU NEED
WHAT YOU NEED
There are 3 methods to create the channel: Hand chisel, router,
or, for the professionals, using a dado blade/table saw. The
most common method is to router out the back of your shelf to
make the room for the female bracket. It is important to note
that the bottom of the bracket is .80mm longer than the top. We
recommend having the the top of the bracket .40mm (a fingernail)
recessed from the shelf & a .40mm overhang for the bottom. This
is to allow for the bracket to slightly embed itself into the drywall
to prevent any unwanted rocking once installed.
STEP 1 - CREATE CHANNEL
STEP 1 - CREATE CHANNEL
Use the 1 1/4” pan head screws to secure the bracket to your
shelf. Please use 1 screw per hole.
STEP 2 - ATTACH FEMALE BRACKET
STEP 2 - ATTACH FEMALE BRACKET
Option 1: You will need to drill & tap the holes in the bottom of the
shelf to accommodate the threaded set screws for the bracket that
we will be using to secure the two components together towards
the end of the installation process.
Option 2: You either can use epoxy glue only to secure both brack-
ets together later in the installation or combine both methods.
Epoxy is a more permanent installation.
STEP 3 - DRILL SET SCREW HOLES
STEP 3 - DRILL SET SCREW HOLES
You will need to drill the necessary holes into the male bracket.
Please use the 3/16” tapper bit. The reason we don’t predrill
the bracket is due to the vast variety in stud separation in each
individual case. It is recommended to find a minimum of 2 studs.
Mark your studs on the bracket & ensure you drill your holes
centered on the provided top & bottom dyelines on the bracket.
STEP 4 - PREPARING THE MALE BRACKET
STEP 4 - PREPARING THE MALE BRACKET
Have a question? Visit our help
center! hovrsolutions.com/learn
