Hoval UltraOil 65 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 44

Hoval UltraOil 65 Скачать руководство пользователя страница 14

14

2.6

Burner assembly

Fig. 1

Remove front cover (1, Fig. 16), after first releasing

the lateral locking bolt (1a) (turn approx. ¼ turn to the

left and pull out as far as the stop). Lift the front cover

(1) straight upwards and remove towards the front.

Fig. 2

Lift and remove the lid (2).

Fig. 3

Remove the locking screw (3) on the left and right.

Fig. 4

Lift the side walls (4), by sliding them slightly to

-

wards the front.

2

4

3

1

1a

4

Fig. 16

Fig. 5

Remove the burner from the packaging.

Fig. 6

Dismount the burner flange. To do so, loosen the

screw (3, Fig. 17) and rotate the burner by 15°. The

required Allen key (2) is supplied with the burner.

2

3

Fig. 17

Fig. 7

Mount the burner flange including sealing to the

boiler flange in accordance with Fig. 18. Mount the

flange so that the “Warning” label is facing outwards.

Tip to help assembly:

To simplify installation, the sealing on the burner flange

can be lubricated using a heat-resistant paste (e.g. Klu

-

berpaste UH1 84-201).

“Warning” label

Fig. 18

Fig. 8Insert the burner rotated by 15° (final position: burn

-

er performance label facing outwards) into the burner

flange. Once the stop position has been reached, ro

-

tate by 15° so that the extension piece fits beneath

the head of the screw (Fig. 19 and Fig. 20).

Fig. 19

4 213 787 / 01

ASSEMBLy

«
...
12
13
14
15
16
...
»

Содержание UltraOil 65













































Отзывы:

Нет отзывов