Hoval CombiVal WP-VT Скачать руководство пользователя страница 8

Страница: 8 / 10

4 209 973 / 00

Fault investigation

The inlet and outlet screens and the evaporator must be checked for
dirt regularly, and cleaned when necessary.

Corrective action

• See fault display

•  Replace fuse
•  Switch on main switch

•  Reset safety thermostat
•  Replace

•  Replace
•  Replace
•  Turn on
•  Check standby, replace

• See fault display

• Clean

• Install
• Fill

Cause

• See fault display

• No power to the plug
• Main switch switched off

• Overheating
• Electrical connection defective

•  Electrical connection defective
•  Pump defective
•  Pump blocked
•  Boiler not in standby position

• High-pressure fault

•  Condensate drainage blocked

•  No drainage siphon installed
•  No water in drainage siphon

Fault

Alarm signal in display

  Electrical fault
  no display

  Electrical heating does not heat
  up, although switched on

Additional heating does not heat up,
although it is switched on

Fault No. 5 or 6

Condensate leak during operation

Smell

You can minimise the risk of a fault
occurring by signing up to a service
contract. If despite this something
goes wrong, go through the

fault checklist. Make sure that you
have adhered to the instructions in
the manual. If nevertheless

the fault cannot be eliminated,
please contact your Hoval
customer service.

Typ CombiVal WP-VT (2141)

Fault investigation

Содержание CombiVal WP-VT











Результаты поиска

Содержание CombiVal WP-VT

Отзывы:

Похожие инструкции для CombiVal WP-VT

Бренды по названию

Популярные бренды

Hoval CombiVal WP-VT, Руководство по эксплуатации

Результаты поиска

Содержание CombiVal WP-VT

Отзывы:

Похожие инструкции для CombiVal WP-VT

Бренды по названию

Популярные бренды