background image

Houston Radar PNL10 User Manual 

 

Page 5 of 32 

INTRODUCTION 

 
Congratulations on your purchase of the Houston Radar directional Doppler radar speed 
sign kit PNL10. This state of the art two-digit speed display with integrated ultra-low 
power 24GHz K-band microwave Doppler radar is specifically designed for the license 
free solar power or battery operated speed sign and traffic calming sign market. 
 
Utilizing high performance, ultra low power DSP (Digital Signal Processing) technology 
and microwave components based on a planar patch array antenna with integrated low 
power PHEMT oscillator, you will find that this high quality product meets your exacting 
standards for performance and reliability. 
 
Some of the highlights of this product include: 
 

 

Zero cables highly integrated design assembles into your enclosure in minutes 

 

10.5” (27cm) digit height with 30% inter-character separation is matched to 300+ ft 
(90+ m) detection range of the radar for optimal display legibility 

 

Best in class power efficiency achieved by: 

 

Low power SS300 radar directly drives display thus eliminating display controller 

 

Built-in ambient light sensing and automatic brightness control 

 

Ambient temperature compensation of the LED drive voltage 

 

High efficiency boost regulator for LED drive voltage 

 

When no traffic is present, the radar automatically powers down display further 
reducing power consumption to only 0.1W 

 

Wide input supply voltage operation allows flexible power supply options ranging 
from 3, 4 or 5 cell Lithium Ion packs to 6 or 12V Lead Acid batteries without 
sacrificing sign efficiency 

 

Built-in rotary switch allows user to set cutoff and violator speed alerts in the field 
without connecting to a computer 

 

White LED strobe light and display flashing can be optionally activated to draw 
attention to speeding 

 

An expansion connector allows addition of a third digit or a fixed custom external 
message, e.g  “SLOW DOWN” when speed violation is detected 

 

Built-in radar is FCC approved with CE mark and available in 24.125GHz and 
24.200GHz versions for worldwide deployment 

 

Advanced In-Radar Traffic Statistics collection option now available 

Содержание PNL10

































Отзывы: