Menu #
Feature
Explanation
Factory
default
Adjustment
(Press up & down buttons to adjust)
01
Mode/Sensor Selection
This thermostat is a combination model which
allows you to choose 3 different modes
A mode = Air Sensing Only (Has built in sensor)
AF mode = Air & Floor sensing
F mode = Floor sensing ( floor probe installed)
A
A / AF / F
02
Switching differential
The number of degrees difference before switching
The default is 1Deg C which means the stat will
switch the heating on 0.5DegC below the set
temperature and will turn it off 0.5DegC above the
set temperature.
With a 2 DegC differential the heating will switch
on 1 DegC below the set temperature and will
switch off 1 DegC above the set temperature.
1 DegC
1 Deg C - 5 Deg C
03
Air Temp Calibration
This is to recalibrate the air temp if required
0DegC
-5 Deg C - + 5 Deg C
04
Floor Temp Calibration
This is the recalibrate the floor temperature if req
0DegC
- 5 Deg C - + 5 Deg C
05
Temp Readout
(AF mode only)
This gives you the option to show the Air Temp,
floor Temp or to show both Air & Floor at intervals
A
A = Show Air Temperature
F = Show Floor Temperature
A-F = Show Floor and Air Temperature in 5 sec
intervals
06
Maximum Floor Temp
( AF Mode only)
This is to protect the floor surface
40 DegC
20 Deg C - 40 Deg C
07
Temperature For-
mat
This allows the temperature to be set to show
Deg Celsius or Deg Fahrenheit
C
Deg C / Deg F
08
Clock Format
You can select the clock to show in either 12
or 24 hour time
24
12 / 24
09
Frost Protection
This is to avoid your room temp going below 5 DegC
Off
On / Off
10
5+2 or 7 Day mode
This allows you to program either 5 days at once,
then the 2 days of the weekend separately,
or a full 7 days at the same time.
01
01 = 5 + 2 Day Programming
02 = 7 Day Programming
Hotwire
Thermostat
Technical Information
To access Menu settings,
1. Press Power button to turn off the thermostat.
2. Press and hold button Prog for three seconds to bring up the configuration menu. Now press Prog button to select each different menu number.
Menu Settings
Page 2
Press , starts flashing, press
or to adjust the setpoint among a range of 5~30 deg C. (for floor mode, the
range will be 5~40 deg C).
Press to confirm.
Press and hold to lock the buttons. A lock icon will display.
Vacation mode is used to drop the heating down to a minimum set temperature to ensure room stays damp free.
Press and hold to unlock the buttons. The unlock icon will display.
220Vac 10%, 50/60Hz
DC 3 V (2 x 1.5 V AAA Alkaline batteries)
Accuracy: ±1
Set-point range: ambient 5~30 deg C
floor 5~40 deg C
Storage: -20~50 deg C
Load Capability: <16 A, 220VAC
deg C
Wiring Diagram & Technical Specifications
Additional Functions
+
230V AC
heating element
Floor Sensor
Probe
N L
M
This product should be installed by a qualified electrician.
Press this tab lightly back and simultaneously push the front
panel upward to release it off the back plate. Wire up the
Thermostat as per the wiring diagram below, then place the
back into the flushbox, and tighten it with the screws provided.
To replace the Thermostat, slide the front panel downward
onto the back plate.
96
40
58
119
Vacation Mode Adjustment
Key Lock & Unlock
Dimensions & Installation
95
51
110
02
F