Hotsy BXA-252739 Скачать руководство пользователя

Страница: 7 / 22

BXA • 8.917-989.0 • Rev. 12/13

PRESSURE

ASHER

OPERA

OR’S MANU

Pump

— Develops high pressure.

Starter

Grip

— Used for starting the engine manu-

ally.

Spray Gun

— Controls the application of water and

detergent onto cleaning surface with trigger device.
Includes safety latch.

Unloader valve

— Safety device which allows pres-

sure tu be released when spray gun is closed

Detergent Injector

— Allows you to siphon and mix

detergents. (Not included with machine)

Wand

— Must be connected to the spray gun.

High Pressure Hose

— Connect one end to water

pump discharge nipple and the other end to spray
gun.

Pump Protector

— Cycles fresh cool water through

pump when recirculating water reaches 140°F/60°C.

Note: If trigger on spray gun is released for more
than 1-2 minutes, water will leak from valve.
Warm water will discharge from pump protec-
tor onto fl oor. This system prevents internal
pump damage.

COMPONENT IDENTIFICATION

Starter Grip

Trigger

Spray Gun

High Pressure

Hose

Pump

Straight

Through Wand

Pressure

Nozzle

Garden Hose

(not included)

Inlet

Screen

Pump

Protector

Unloader

Detergent

Bucket

(not included)

Hose

Detergent

ENGINE

Detergent

Injector

(Not Included)

PUMP

Содержание BXA-252739























Результаты поиска

Содержание BXA-252739

Отзывы:

Похожие инструкции для BXA-252739

Бренды по названию

Популярные бренды

Hotsy BXA-252739, Руководство оператора

Результаты поиска

Содержание BXA-252739

Отзывы:

Похожие инструкции для BXA-252739

Бренды по названию

Популярные бренды