background image

4

How To Use This Manual

This manual contains the following sections:

How to Use This Manual

Safety

Operations

Maintenance

The HOW TO USE THIS MANUAL section will tell you 
how to find important information for ordering correct 
repair parts.

Parts may be ordered from authorized dealers. When 
placing an order for parts, the machine model and 
machine serial number are important. Refer to the 
MACHINE DATA box which is filled out during the 
installation of your machine. The MACHINE DATA box 
is located on the inside of the front cover of this manual. 

The model and serial number of your machine is 
located on the back of the machine.

The SAFETY section contains important information 
regarding hazardous or unsafe practices of the 
machine. Levels of hazards are identified that could 
result in product damage, personal injury, or severe 
injury resulting in death.

The OPERATIONS section is to familiarize the operator 
with the operation and function of the machine.

The MAINTENANCE section contains preventive main-
tenance to keep the machine and its components in 
good working condition. They are listed in this general 
order:

Pump

Heating  Coil

Troubleshooting

Model:

Date of Purchase:

Serial Number:

Dealer:

Address:

Phone Number:

Sales Representative:

MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP    9.808-037.0-A 

Содержание 1800 Series































Отзывы: