Hotsy 1710, Инструкция по эксплуатации и каталог запасных частей

Страница: 6 / 42

6
1700 SERIES PRESSURE WASHER
OPERATOR’S MANUAL
Hotsy 1700 • 97-6419 • Rev. 7/06
WARNING: High pressure spray
can cause paint chips or other
particles to become airborne and
fly at high speeds.
10. Eye safety devices and foot
protection must be worn when
using this equipment.
11. Machines with spray gun should
not be operated with the trigger
in the off position for extensive
periods of time as this may cause damage to the
pump.
12. Protect from freezing.
13. Be certain all quick coupler fittings are secured
before using pressure washer.
14. Do not allow acids, caustic or abrasive fluids to pass
through the pump.
15. Inlet water must be cold and clean fresh water.
16. To reduce the risk of injury, close supervision is nec-
essary when a machine is used near children. Do not
allow children to operate the pressure washer.
this
machine must be attended during operation.
17. The best insurance against an accident is precaution
and knowledge of the machine.
18. Hotsy will not be liable for any changes made to
our standard machines or any components not
purchased from
Hotsy .
pre-operation check

Read machine safety warnings

Pump oil (SAE 30W (non-detergent oil))

Cold water supply (1gpm over machines rating •
5/8" • 20 psi)

Proper power supply and circuit protection

Hose, wand, nozzles (nozzle sizes per serial
plate)

Water filter (intact, non restrictive)

Read operation instructions

This machine must be protected from the elements/
freezing.
set-up procedures
this machine is intended for indoor use. machine
must be stored indoors when not in use.
1. Attach a minimum 5/8" garden hose to inlet connec-
tor. Minimum flow should be 1 gpm over the flow rate
of the pressure washer.
2. Attach high pressure hose to discharge nipple using
quick coupler. Lock coupler securely into place by
pulling back coupler collar and inserting it onto dis-
charge nipple, then pushing collar forward to lock in
place.
3. Attach wand to spray gun using teflon tape on
threads to prevent leakage.
4. Attach connector on discharge hose to spray gun
using teflon tape on threads.
5. Remove oil plug on top of pressure washer pump
and replace with dipstick supplied. (This may be
installed from the factory.)
6. Check oil level on oil dipstick on top of pump. Oil
should be visible one half way up sight glass (30W
non-detergent).
operatinG instructions
1. Read safety and preventative maintenance instruc-
tions before starting machine.
2. Turn on water at faucet and pull trigger on spray gun
allowing water to flow until all air has discharged from
system. Check for water leaks; tighten as needed.
3. Push the pump switch on.
4. Turn the variable pressure control handle clockwise
to increase pressure.
5. To apply detergent read “How to Use The Detergent
Injector.”
shut doWn procedures
1. Rinse with clean water to remove any soap residue,
by placing detergent hose into fresh water bucket
and operating injector as described below.
2. Release the trigger on the spray gun. Turn the switch
off if the machine is going to be left unattended.
(Time delay only).
3. Turn off water supply.
4. Open spray gun to relieve remaining pressure.
5. Remove water supply hose.
WarninG
USE PROTECTIVE
EYEWEAR WHEN
OPERATING.
Selection of high or low pressure is accompanied by
turning the handle.
note: High pressure nozzle must
be inserted at end of wand to obtain high pressure. To
apply soap read operator's manual.
variable pressure
control handle
trigger
variable pressure
Wand (vp)
high
pressure
nozzle
brass soap
nozzle