Y
5
Y
5
“Doorway Learn” is ON
Ref section 7, Dip Switch Settings.
Green LED blinks for about 10s as the “door learn” process is
carried out. Door opens/closes.
Presence Detection:
During the “Doorway Learn” process the outer 4 rows of detection on the HR100-CT sensor
switch from motion detection to presence detection 10s after power ON. The inner “door learn” row of detection will
switch from motion to presence detection after the “doorway learn” process is carried out.
Upon power ON, the Red LED
indicates a door open relay output
to begin the doorway learn process.
Door learn process complete,
sensor in standby mode.
“Doorway Learn” is OFF
Ref section 7, Dip Switch Settings.
Upon power ON, the solid green LED turns on indicating
that the sensor is in standby mode and ready to detect.
Presence Detection:
It
takes
10s
after
sensor
power
up
for
presence
detection
to
be
initiated
on
all
rows
of
detection.
If
before 10s
has
elapsed
someone
walks
into
the
detection
area
it
will
take
about
5s
after
the
person
leaves
the
detection
zone
for
presence
detection
to
be
functional.
9.
APPLYING
POWER
AND
THE
“
DOORWAY
LEARN
”
SETTING
Note
When
carrying
out
the
following
work,
turn
off
sensor power.
※
When the floor condition is changed by placing a mat on the floor etc.
※
When the detection area pattern or sensor sensitivity is adjusted.
When Doorway Learn is turned ON, the sensitivity level of the inner row of detection is only at maximum when the outer
rows of detection are activated.
Red solid LED
Green blinking LED
Green blinking LED
Green solid LED
Green solid LED
CAUTION
!
General Caution:
Technical problems with the HR100-CT sensor are indicated by a flashing Green/Red LED. The frequency of
flashing indicates the type of problem as explained below.
13. SELF DIAGNOSTICS ERRORS
11.
TIMING
CHART
OF
EVENTS
After
installation
is
completed “walk test” the sensor detection area. If the detection area is not as expected adjust the
detection area as referred to in section 8 or increase the rows of detection using
Dip switch X 3 & 4
If the detection area is still not as expected then the sensor sensitivity can be increased by turning the potentiometer
clockwise. When the sensor detects even though there is nothing in the detection area the sensor sensitivity can be
decreased by turning the potentiometer in the anti-clockwise direction.
Sensitivity
H
L
10.
VERIFICATION
OF
OPERATION
When carrying out door maintenance work with power applied to the
sensor on door controllers that are wired to “test” the sensor ensure to
set the dip switches as below.
12.
DOOR
MAINTENANCE
WORK
Note
NON-DETECTION
D E T E C T I O N
A s
response
to
TEST
POWER
OFF
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
DETECTION
NON-DETECTION
TEST
RESPONSE
1
2
3
4
5
T1
T2
NON-TEST
TEST
TEST
Test
Input
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Safety
Output
Row
1,
2
/
Test
Input
Activation
Output
Row 2, 3, 4, 5
1
2
3
4
5
Yellow
Blue
Yellow
Blue
TEST
NON-TEST
NON-TEST
OFF
6
ON
7
N.C.
Dip
Switch
X
Dip
Switch
Y
NON-DETECTION
POWER
OFF
1
2
3
4
5
DETECTION
White
Green
White
Green
White
Green
White
Green
White
Green
White
Green
1
2
3
4
5
1
2
3
4
5
2
N.C.
Dip
Switch
Y
Keep
in
mind to return the dip switch settings to their original
state once door maintenance work has been carried out.
N.O.
N.O.
Flash
Frequency
Red
Green
Red
Green
Fast
Slow
LED
Cause
Please
replace
the
sensor.
T1
:
10±1
[mSec]
App
T2
:
11±1
[mSec]
App
Sensor
Brown
Gray
Break
the
current
flow
on
test
state.
Supplying
DC12
to
24V,
make
current
flow
from
Gray
to
Brown.
Sensor
Brown
Gray
Sensor
Brown
Gray
O
N
1
2
3
4
5
6
7
8
Refer to [7.Dip
Switch
Settings].
Dip
Switch
X
2s
1 2
Low
Ref.
8
“Doorway Learn” Failure & Recovery:
If a person enters the detection area during the “doorway learn” process it
may not be successfully completed. In this case the sensor will carry out the doorway learn process on
door
activations by a person in order to build an accurate image of the door open and door close position.
14. TROUBLESHOOTING
Detection
row
“ROW1” (
“
ROW2
”
when “Doorway
Learn
”
is turned ON) is focused too close to the door.
LED
Status
Possible
Cause
Solution
Door
does
not open when a
person enters the detection
area.
OFF
Door opens and closes for no
apparent reason (Ghosting).
Object
moving
in
the
detection
area.
Sensitivity
too
high for the installation environment.
Dust, frost or water droplet on the sensor lens.
Detection area overlaps with that of another sensor.
ORANGE
Door opens and remains in the
open position.
Detection area changed, while
∞
infinity
presence timer setting is in use.
ORANGE
blinking
(Slow)
Door Hold (Dip switch
Y
4 set to Open).
Detection of falling snow, insects, leaves etc.
RED
Incorrect sensor wiring.
Reflected signal saturation.
Remove highly reflective objects from the detection
area, or lower the sensor sensitivity.
Remove the
moving
object
from
detection
area.
Reduce the sensor sensitivity.
Wipe the sensor lens clean and install a weather cover if necessary.
Ensure
different
frequency
setting
for
each
sensor.
Turn monitor mode Dip
switch Y 3 to “Snow”.
Adjust
detection
depth
of
Inner
3
rows
away
from
the
door.
Re-power
the
sensor
or
change
the
presence
timer
settings
to
30
or
60
secs.
Turn “Door Hold” Dip
switch
Y
4
to
Auto.
When
Door
opens
or
closes,
LED
ORANGE.
Door
Opens
RED
Door
Closes
GREEN
Problem
Sensor
Connector not connected correctly.
Incorrect power supply voltage.
Incorrect sensor wiring.
Apply
proper
voltage
to
the
sensor.
(AC/DC
12-24V)
Tighten
or
reconnect the connector.
Double check sensor wiring.
Double check sensor wiring.
Compiler
of
Technical
File
(EC
Community)
David
Morgan
Hotron
Ireland
Ltd
26
Dublin
Street,
Carlow,
Ireland
Ph:
+353-(0)59-9140345
Fax:
+353-(0)59-9140543
Description
of
Product:
HR100-CT
Combined motion and presence
detection sensor for the activation and safety
of automatic doors.
Technology
used
is
Active
Infrared
Technology.
Directives
Fulfilled:
DIRECTIVE
2006/42/EC
DIN
18650-1:2005
Powered
pedestrian
doors
Part
1:
Product
requirements
chapter
5.7.4
EN12978:2003
Industrial,
commercial
and
garage
doors
and
gates
-
safety
devices
for
power
operated
doors
and
gates
-
Requirements
and
test
methods
EN62061:2005
Functional
safety
of
electrical/electronic/programmable
electronic
safety-related
systems
EN
ISO
13849-1:2008
Safety
of
machinery
-
Safety-related
parts
of
control
systems.
EN
16005:2012
EC type examination 44 205 12 414283-001
Above
EC
Type
Directives Certified
by:
TUV
NORD
CERT
GmbH
30519
Hannover,
Germany
Identification
No:
0044
Harmonized
Standards
Used:
EN
ISO
13849-1:2008
Other
Technical
Standards
Used:
DIN
18650-1:2005
EN
16005:2012
Declaration
made
by
Kaoru
Musya
General
Manager. Honda
Electron
Date
9
th
of
Nov.
2012
Location
of
Declaration
Honda
Electron
Co.,
LTD.
1-23-19
Asahi-Cho,
Machida-City,
Tokyo,
Japan
15. HR100-CT EC DECLARATION OF CONFORMITY
<
Disclaimer
>
The
manufacturer
cannot
be
held
responsible
for
below.
1.
Misinterpretation
of
the
installation
instructions,
miss
connection,
negligence,
sensor
modification
and
inappropriate
installation.
2.
Damage
caused
by
inappropriate
transportation.
3.
Accidents
or
damages
caused
by
fire,
pollution,
abnormal
voltage,
earthquake,
thunderstorm,
wind,
floods
and
other
acts
of
providence.
4.
Losses
of
business
profits,
business
interruptions,
business
information
losses
and
other
financial
losses
caused
by
using
the
sensor
or
malfunction
of
the
sensor.
5.
Amount
of
compensation
beyond
selling
price
in
all
cases.
MP-10120-A
'13.09
26
Dublin
Street
(2nd
Floor),
Carlow,
Ireland
URL:
http://www.hotron.com
Fax:
+353-(0)59-9140543
Phone:
+353-(0)59-9140345
1-11-26 Hyakunin-Cho,
Shinjuku-Ku,
Tokyo,
Japan
URL:
http://www.hotron.com
Fax:
+81-(0)3-5330-9222
Phone:
+81-(0)3-5330-9221
R
Manufacturer
HOTRON
CO.,LTD.
SALES
Europe
Hotron
Ireland
Ltd.
Activation
Output
Test Input setting
Safety
Output
Confirm
that
the
sensitivity
potentiometer
is
set
to
maximum and re-power the sensor.
If
the
error
persists, set
Dip
Switch
X
8 to
“Low Reflection”.
GREEN/RED
SLOW FLASH
Reflection of the transmitted infrared signal from
the floor is too low.
Increase sensor sensitivity or change the “Reflection Diagnostics”
Dip
switch
X
8 from “Normal” to “Low Ref”.
GREEN/RED
FAST FLASH
Internal sensor error.
Replace the sensor.
Draft
