SETTINGS WITH REMOTE CONTROL
Domi-LINK
The Domi-LINK allows to set the radar sensor unit easy, fast and perfectly from the floor.
While the programming the sensor functions are still active. The settings can be checked immediately.
Low batteries (shown on the Domi-LINK display), sunlight, fluorescent lamps and wrong orientation of Domi-LINK
can reduce the range and cause transmission errors.
For safety reasons the IR-programming mode will be intermitted after 30 min., alternatively completely blocked.
To unlock the programming mode, push the MENU or VALUE button at the radar sensor unit or cut the power supply for a few seconds.
Establish connection
Before starting the programming please read the Domi-LINK operating instructions!
Sensor switched of and ready for operation, LED is green.
Domi-LINK must point frontal at the sensor.
For a perfect transmission the
sensor angle (0 – 40°) should
Sensor list
Domino 100X RC
Domino 101X RC
Domino 102X RC
Domino 110X RC
also be considered.
Choose the Domino 110X RC from the sensor list shown at the Domi-LINK LCD-display.
After that select the address, only necessary if more than one sensor is inside the range of Domi-LINK.
Programming the address
→
have a look at the settings with buttons.
The address can be selected from the list or can be read out with “search address“.
Domino 110X RC
search address
address 2
address 3
address 4
address 1
The mark show the selected address.
Push the select button to establish a connection to the radar sensor unit.
If the connection is established, on LCD display will be shown a list with all settings.
The mark shows the current settings.
If the sensor is encoded, the display will show “enter code”.
The code can be set with the for Domi-LINK push buttons.
As soon as the fourth digit has been set the code will be transmitted.
_ _ _ _
enter code
Domino 110X RC
Detection mode
Vehicle detection
Output hold time
Relays contact
Fade out cross traffic
Sensitivity
√
If the code is correct a selection list will appear on display.
Start settings
The four push buttons allow to select the desired settings shown on display.
With “read value” the current setting can be read out and shown on display. The required value can be
selected with the arrow push buttons and confirmed and transmitted with pushing the select button.
The mark shows immediately the new value.
If the transmission was not OK the error will appear on display and the transmission has to be repeated.
Sensitivity
read value
1 min
2
3
4
The new setting can be read out immediately after the transmission.
Programming table Domi-LINK
MENU SETTINGS
DESCRIPTION
Sensitivity
1 – 16
1 = lowest sensitivity = small detection area
16 = highest sensitivity = big detection area
Detection mode
off
stereo forwards
stereo backwards
mono
off = no detection possible
detects motion
towards the radar sensor unit
detects motion away from the radar sensor unit
detects motion forwards and backwards
Vehicle detection
off
low
medium
high
off = no detection the vehicle relays does not switch
only vehicles will be detected
the settings low, medium and high allow to set the sensor accurate according to the localization
Output hold time
off
0.2s
0.5s
1.0s
1.5s
2.0s
3.0s
4.0s
5.0s
off = relay does not switch
0.2s = smallest hold time
1.0s = factory setting
5.0s = biggest hold time
Relay contact
N.O.
N.C.
contact will close by detection
detection mode switched off and the change of relay contact
contact will open by detection
will keep the gate constant open or closed
Fade out cross traffic
off
low
medium
high
all movements well be detected
cross traffic will be fade out
the settings low, medium and high allow to set the sensor accurate according to the localization
Reset
put all values back on factory setting
Code
access with code
*
lock access
access without code
set an access code access to programming mode only with code possible
code and programming mode will be locked immediately, new access not possible anymore*
code will be deleted, programming mode is free access to programming mode without code possible
Disconnect
leave programming mode, access is encoded, decoded or locked immediately, according to setting
*
lock access
If you lock access, the programming mode will be locked immediately. The radar sensor unit will not accept any commands from the remote control.
To unlock the programming mode, push the MENU or VALUE button at the radar sensor unit or cut the power supply for a few seconds.
