Hotpoint RZAAV21 Series Скачать руководство пользователя

Страница: 2 / 12

Installation

Connection of the water supply

To carry this out, use the kit provided which contains
all the necessary elements for connection to the water
supply.
To improve the performance of the Aqua Care, we
recommend that you fit a tap with a filter on the pipe for
the connection to the water system: in this way it will be
possible to manually interrupt the water supply during
long periods in which Aqua Care is not used.

The water pressure inside the water system must be

between 0.8 bar and 8 bar.

The appliance must only be connected to a water

supply suitable for drinking.

Your appliance is supplied with a 13amp fused plug that
can be plugged into a 13amp socket for immediate use.
Before using the appliance please read the instructions
below.

WARNING:
THIS APPLIANCE MUST BE EARTHED.

Replacing fuse covers:

When replacing a faulty fuse, a 13amp ASTA approved
fuse to BS 1362 should always be used and the fuse
cover re-fitted.
If the fuse cover is lost, the plug must not be used until a
replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the
correct colour as indicated by the coloured marking or the
colour that is embossed in words on the base of the plug.

Changing the plug:

Removing the plug

If your appliance has a non-rewireable moulded plug and
you should wish to remove it to add a longer cable or
to re-route the mains cable through partitions, units etc.
please ensure that either:
- The plug is replaced by a fused 13amp re-wireable

plug bearing the BSI mark of approval.

or
- The mains cable is wired directly into a 13amp cable

outlet, controlled by a switch (in compliance with
BS 5733) which is accessible without moving the
appliance.

Disposing of the plug

Cut off and dispose of the supplied plug if it does not

Before placing your new appliance into operation

please read these operating instructions carefully. They
contain important information for safe use, for installation
and for care of the appliance.

Please keep these operating instructions for future

reference. Pass them on to possible new owners of the
appliance.

Positioning and connection

Positioning

1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and

condenser give off heat and require good ventilation to
operate correctly and save energy.

3. Leave a space of at least 10 cm between the top part of

the appliance and any furniture above it, and at least 5 cm
between the sides and any furniture/side walls.

4. Ensure the appliance is away from any sources of heat

(direct sunlight, electric stove, etc.).

5. In order to maintain the correct distance between

the appliance and the wall behind it, fit the spacers
supplied in the installation kit, following the instructions
provided.

Levelling

1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the

refrigerator by tightening or loosening the rear feet.

Electrical connections

After the appliance has been transported, carefully place
it vertically and wait at least 3 hours before connecting it
to the electricity mains. Before inserting the plug into the
electrical socket ensure the following:

• The appliance is earthed and the plug is compliant

with the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate located
inside the freezer (e.g. 150 W).

• The voltage is in the range of values indicated on the

data plate located inside the freezer (e.g. 220-240V).

• The socket is compatible with the plug of the appliance. If

the socket is incompatible with the plug, ask an authorised
technician to replace it (see Assistance). Do not use

extension cords or multiple sockets.

Once the appliance has been installed, the power

supply cable and the electrical socket must be easily
accessible.

The cable must not be bent or compressed.