55
en
Heating or frothing the milk – Automatic
operation
1. Place the container on the base.
2. Remove the milk container’s lid.
3. Fit the appropriate whisk into the holder on the
bottom of the container.
4. Pour the desired amount of milk into the contai-
ner.
5. Fit the lid back onto the container.
6. Use the temperature knob to set the desired
temperature.
7. Insert the power plug into a suitable wall power
outlet. The main led will light up.
8. Press the ON button. The appliance will beep,
the led will start flashing and the frother cycle will
start.
9. When the milk reaches the set temperature, the
cycle automatically stops. If you set cold froth
mode with the knob, the cycle will stop auto-
matically after 60 seconds.
10. The appliance will beep three times when the
cycle terminates.
11. You can interrupt the cycle at any time by pres-
sing the start/stop button. The set temperature
will not be reached if you do so.
12. Once the cycle has terminated, remove the con-
tainer from the base and pour its contents into
a cup or mug. You can use a spoon to push the
froth out of the container, or simply shake the
container slightly while pouring.
13. You can now disconnect the plug from the wall
outlet.
Heating – Keep warm function
This function allows you to froth or heat the milk and
keep it hot at the set temperature. Follow steps 1 to 7
in the previous paragraph.
8. Hold down the start button for more than 2 se-
conds. The appliance will emit a long beep, the
led will start flashing and the frother will start
operating.
9. When the milk reaches its set temperature, the
appliance will stay on for a while before switching
off:
•
20 minutes for the 40°C cycle
•
10 minutes for the 65° and 85° cycles
10. You can interrupt the cycle at any time by pres-
sing the start/stop button.
11. Once the cycle has terminated, remove the con-
tainer from the base and pour its contents into
a cup or mug. You can use a spoon to push the
froth out of the container, or simply shake the
container slightly while pouring.
12. You can now disconnect the plug from the wall
outlet.
This feature is not suitable to keep warm the
milk froth and other drinks like hot chocolate.
FOR BEST RESULTS...
To get the best results, take the milk out of the refrige-
rator immediately before pouring it into the container.
•
If you want a rich milky froth, first run the cold
froth cycle and then a hot froth cycle.
•
We recommended using full fat milk for all fro-
thed milk beverages, as it gives a richer froth.
FURTHER INFORMATION
•
If the appliance has been left connected to the
power outlet for a long time after use, you must
press the start button twice to turn it on and then
start a cycle.
•
Allow the appliance to cool down after using a
hot cycle; do not use it immediately for a second
cycle. Wait a few minutes between cycles.
•
After a cold froth cycle, you can immediately
start a new heating or frothing cycle.
MAINTENANCE AND CLEANING
•
Always pull the power plug out of the wall outlet
and wait for its motor to stop completely before
cleaning the appliance.
•
To avoid the risk of electric shock, do not clean
the base or power cord with water, and never im-
merse them in water.
•
The container, whisks and lid can be cleaned
with hot water and a mild detergent, or in the di-
shwasher.
•
Take care to dry all parts thoroughly before using
them again.
•
The heating base can be cleaned with a soft
damp cloth which has been dipped in a small
amount of detergent. Never immerse it in water
or clean it in a dishwasher.
•
Do not use abrasive or aggressive detergents.
Содержание MF IDC AX0
Страница 1: ...EN Operating Instructions ...
Страница 2: ...1 3 4 7 8 2 10 5 6 9 11 12 13 MF IDC UK 220 240V 500W ...
