GB
11
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Grease/odour filter warnings
The bar at the top left flashes to indicate
that the grease filter is saturated.
The bar at the top right flashes to indicate
that the odour filter is saturated.
If both bars are flashing, then both filters
are saturated.
You must then clean/replace the grease filter (
A
) or odour
filter (
B
) or both, accordingly (see “Maintenance and care”).
The latter only applies to the filter version.
To reset the filter counter:
Hold down
T4
for three seconds while the hood is on.
If both filter warnings are active at the same time, you must
reset each separately.
The first sequence resets the grease filter, while the second
sequence resets the odour filter.
Ducted
(square at bottom left flashing).
Filter
(square at bottom right flashing).
You can change the type of installation by pressing
T4
. To
quit configuration mode, press
T1
once; this switches the
unit off and saves the last displayed setting.
Maintenance and care
Caution! Before cleaning or servicing the unit,
disconnect it from the mains by pulling the power plug
or disconnecting the main circuit breaker.
First cleaning
• Remove the protective film
• Clean with a damp sponge and a little neutral soap
• Rinse off with a damp cloth
• Dry with a soft cloth; if the hood is stainless steel, dry
along the metal's grain
Periodic cleaning
The hood must be cleaned frequently (at least as often as
you service the grease filter), inside and out. Use a damp
cloth and a neutral liquid detergent with lukewarm water.
Do not use abrasive or corrosive products.
Warning:
Failure to observe the hood cleaning and filter
cleaning/replacement instructions can result in fires. Follow
the instructions carefully. The manufacturer is not liable for
any damage to the motor or fires caused by incorrect care
or failure to follow the above instructions.
Servicing the grease filter (A)
A
The grease filter retains the
particles of grease produced
during cooking; it must be
cleaned at least once a month
w i t h a n o n - a g g r e s s i v e
detergent, either by hand or
with a low temperature, short
dishwasher cycle.
To extract the grease filter,
pull the spring loaded handle.
If washed in a dishwasher, the metal filter may change
colour, but this does not affect its performance.
Servicing the charcoal filter (B)
B
The charcoal filter retains
unpleasant cooking odours.
The filter saturates after a
variable time, depending on
the type of cooking and how
often the grease filter is
cleaned. The cartridge must
be replaced at least once
every twenty months.
This filter can NOT be washed
or regenerated
Disassembly:
Rotate the filter 90° to remove it from the
suction assembly.
Assembly:
Fit the active-carbon filter into the suction
assembly and rotate it 90° to secure it in place.
Replacing the bulbs
Disconnect the unit from the mains and remove the grease
filter.
Caution!
Make sure the bulbs are cool before touching
them.
1. Extract the guard
by prising it out with a small
flat head screwdriver or
something similar.
2. Replace the faulty bulb.
Use only bulbs of the
same type (for details,
see the technical data in
the following manual).
3. Refit the guard (push it in).
Confi guring the hood
To set the operating mode of the hood, hold down
T4
for
6 seconds while the product is off.. After a long beep, the
type of installation displays:
Содержание HDA6.5SAB
