II. DETAILED TRACK ASSEMBLY
a.
Your race set makes two different layouts. Refer to the Assembly Map for
detailed track assembly. Start with the Terminal Track
A
and continue
adding track pieces until your layout is complete.
b.
Once your layout is assembled, you’ll need
to add guardrails. Refer to the Assembly Map
for placement. To attach a guardrail: gently
flex the guardrail before attaching it. Carefully
attach the bottom of the guardrail first. Then
pull up and snap into place. Don’t force guard-
rails into place.
1.
There are letters molded into each
track piece. These letters are used in
these instructions to indicate which
track piece goes where. Following the
layout drawings on the Assembly Map,
you may want to lay out your track
– without connecting any track pieces.
That way you’ll be able to see how the
track layout goes together.
2.
To connect track pieces: working on
the flat surface, push the ends of the
track pieces together. Make sure they
snap together securely – you’ll hear a
click when they’re properly connected.
Remember: if the track connections
aren’t right, electric power won’t flow
from one track section to the next.
3.
To disconnect track pieces,
simply reach underneath where the
track pieces meet and press the
locking tabs together with thumb and
forefinger as shown.
Follow the step-by-step instructions to set up your race set.
Please separate the “Assembly Map” page, and keep it handy during assem-
bly. This page contains the contents list and large-scale Layout Drawings of
the fully-assembled track. You’ll need to refer to it as you go.
The Assembly Map looks like this:
INSTRUCTION MANUAL
Be sure to check out the Troubleshooting Guide on the back of the
Assembly Map.
I. BASIC TRACK ASSEMBLY
Start out on a clean, hard, flat racing surface – not carpeting. Take out all the
track pieces (and other parts) and check them carefully against the contents
list on the Assembly Map.
Sometimes brand-new track may need a quick cleaning for best
performance. Check the Maintenance section of this manual for more
information.
Occasionally the metal track rails will stick up too far from the surface
Occasionally the metal track rails will stick up too far from the surface
of a track piece, as shown. This may interfere with vehicle movement. To
of a track piece, as shown. This may interfere with vehicle movement. To
correct, simply press the rail back down with your finger. If the problem
correct, simply press the rail back down with your finger. If the problem
persists, please contact Customer Service toll-free at 1-888-557-8926
persists, please contact Customer Service toll-free at 1-888-557-8926
(see hours of operation in the Warranty section).
Keep these instructions
for future reference, as they contain important information.
Look for this symbol
throughout this manual. It indicates important infor-
mation.
START HERE!
START HERE!
ADULT ASSEMBLY REQUIRED.
5+
®
MAIN LAYOUT DRAWING
Refer to the package for color photographs of the assembled layouts.
This page shows the contents list and large-scale Layout
Drawings of the fully-assembled track (tracks are not drawn to scale).
You'll need to refer to it as you assemble your race set.
Refer to the Instruction Sheet for detailed step-by-step instructions
for setting up and using your race set.
8
GUARDRAILS
6
F
9" RADIUS CURVE
1
C
6" STRAIGHT
1
A
9" TERMINAL TRACK
1
SANDPAPER
1
S
15" SQUEEZE
2
CONTROLLERS
1
2
3
1
3
= GUARDRAILS
= TRACK SUPPORTS
1 = Beginner
2 = Average player
3 = Skilled player
1
2
3
2
#2 SUPPORTS
1
6
CLIPS
Use either a diorama or a guardrail on the outside of the curves.
1
BATTERY PACK
F
F
F
F
S
C
A
1
1
F
F
C
S
F
F
F
F
A
1
2
3
1
2
3
ALTERNATE LAYOUT DRAWING
K4578-0921
© 2006 Mattel, Inc., PRINTED IN CHINA. All Rights Reserved.
1
VEHICLE
1
VEHICLE
CHOKING HAZARD –
Small parts.
Not for children under 3 years.
WARNING:
!
