II. DETAILED TRACK ASSEMBLY
a.
Your race set makes two different layouts. Refer to the Assembly Map for
detailed track assembly. Start with the
Terminal Track
and continue adding track
pieces until your layout is complete.
b.
Once your layout is assembled, you’ll need to
add guardrails. Refer to the Assembly Map for
placement. To attach a guardrail: gently flex the
guardrail before attaching it. Carefully attach
the bottom of the guardrail first. Then pull up
and snap into place. Don’t force
guardrails into place.
1.
There are letters molded into each
track piece. These letters are used
in these instructions to indicate
which track piece goes where.
Following the layout drawings on
the Assembly Map, you may want
to lay out your track – without
connecting any track pieces. That
way you’ll be able to see how the
track layout goes together.
2.
To connect track pieces: working on the flat surface, push the ends of the track
pieces together. Make sure they snap together securely – you’ll hear a click
when they’re properly connected.
3.
To disconnect track pieces,
simply reach underneath where the
track pieces meet and press the locking
tabs together with thumb
and forefinger as shown.
Follow the step-by-step instructions to set up your race set.
Please separate the “Assembly Map” page, and keep it handy during
assembly. This page contains the contents list and large-scale Layout
Drawings of the fully-assembled track. You’ll need to refer to it as you go.
The Assembly Map looks like this:
M0676-0921
© 2008 Mattel, Inc. All Rights Reserved.
SPEED RACER MOVIE: © Warner Bros. Entertainment Inc.
SPEED RACER: ™ Speed Racer Enterprises, Inc.
(s08)
MAIN LAYOUT DRAWING
ALTERNATE LAYOUT DRAWING
Refer to the package
for color photographs
of the assembled layouts.
This page shows the contents list and large-scale Layout
Drawings of the fully-assembled track (tracks are not drawn to scale).
You'll need to refer to it as you assemble your race set.
Refer to the Instruction Sheet for detailed step-by-step instructions
for setting up and using your race set.
8
GUARDRAILS
6
F
9" RADIUS CURVE
1
C
6" STRAIGHT
1
A
9" TERMINAL TRACK
1
VEHICLE
1
VEHICLE
1
SANDPAPER
1
S
15" SQUEEZE
2
CONTROLLERS
1
2
3
1
BATTERY PACK
6
CLIPS
1
= GUARDRAILS
= TRACK SUPPORTS
1 = Beginner
2 = Average player
3 = Skilled player
1
2
3
1
CARD BOARD
2
#2 SUPPORTS
1
Use either a diorama or a guardrail on the outside of the curves.
F
F
F
F
S
C
A
1
1
F
F
C
S
F
F
F
F
A
1
2
1
2
3
1
2
3
Be sure to check out the Troubleshooting Guide on the back of the
Assembly Map.
I. BASIC TRACK ASSEMBLY
Start out on a clean, hard, flat racing surface – not carpeting. Take out
all the track pieces (and other parts) and check them carefully against
the contents list on the Assembly Map.
Sometimes brand-new track may need a quick cleaning for best
performance. Check the Maintenance section of this manual for more
information.
Look for this symbol
throughout this manual. It indicates important
information.
START HERE!
Occasionally the metal track rails will stick up too far from the surface
of a track piece, as shown. This may interfere with vehicle movement.
To correct, simply press the rail back down with your finger. If the
problem persists, please contact Customer Service toll-free at 1-888-
557-8926 (see hours of operation in the Warranty section).
Remember: if the track connections aren’t right, electric power won’t
flow from one track section to the next.
ADULT ASSEMBLY REQUIRED.
CAUTION:
This product contains a
sharp edge(s). For adult assembly
only. Take extra care during
unpacking and assembly.
M0676-0920
5+
INSTRUCTION MANUAL
Keep these instructions
for future reference, as they contain important information.
®
