Remove The
Paper Backing
Remove The
Paper Backing
Paper
Backing
Sheet
Remove The Paper Backing From ONE area
Press The Quadrant Onto The Dish
Work on
ONLY ONE Petal
at a Time
Work on
ONLY ONE Petal
at a Time
Remove the protective paper sheet from the back of
ONE entire heater quadrant exposing the adhesive.
Hold the heater blanket up off the dish and continue
on to Step #11.
Smoothly press the quadrant into position and remove air
pockets by following the pattern shown below. Press the
center down and then radiate outward to the edges. Attach
all three remaining quadrants down onto the dish surface
in the same fashion.
The HotShot has a snap-action bimetallic thermostat inside the plastic
cylindrical housing on the face of the heating element. When the
temperature outside approaches freezing, typically at approximately 40
º
F,
the thermostat snaps ‘closed’ and applies power to the resistance heating
strips.
As the temperature of your antenna warms above freezing, typically at
approximately 49
º
F, the thermostat bimetallic strip detects the temperature
change, snaps ‘open’ and turns the HotShot resistance heat strips off.
100~240 Vac
Thermostat
Power Supply
Heater
10
11
W
arrants this product to be free from defects in materials and
workmanship under normal use and service. If our examination
reveals to our satisfaction that the part in question is defective,
we agree to repair or replace it after the unit is returned to us,
prepaid, with proof of purchase. This warranty does not cover
any costs associated with the removal or replacement of the part(s)
in question, the labor to package parts for shipment or the freight
charges incurred to and from the factory. Paint finish or
appearance is not covered by this warranty.
The HotShot electrical components consisting of the heating
element, thermostat and power supply have a
one year
repair or
replacement warranty. Removal labor or reinstallation labor is not
included.
This warranty shall not apply to any product which has been
repaired or altered in any way so as, in our judgement, to affect its
structural integrity or durability; nor shall it cover any damage due to
misuse, negligence, improper installation, or failure of any
supporting structure not supplied by this manufacturer. This limited
warranty does not cover products which have been impaired or
damaged due to severe weather conditions such as, but not limited
to, excessive wind, ice, storms, lightning, or any other natural
occurrences over which PERFECT 10, Inc. has no control.
This warranty is in lieu of all other guarantees expressed or
implied. We neither assume nor authorize any representative or
any person(s) to assume any other liability or assurance in
connection with our product. Non-compliance with any part of
this claim procedure or improper registration of the product at
the time of its original installation may invalidate this warranty in
whole or in part.
Warranty
When the HotShot is in the proper position press the
exposed adhesive surface down onto your dish.
Smooth and remove air bubbles by pressing as shown.
TAKE YOUR TIME with this procedure. Do not remove any
other paper sheets until this center section is pressed into
place.
Route the supplied lead wire from the blanket to the power supply
location.
TRIM
any excess wire, do not leave excess wire coiled up.
Strip both ends and connect to the power supply utilizing the two screw
posts. It does not matter which wire you connect to which post.
Connect the AC power cord and plug into 120VAC outlet.
NOTE - Red LED only illuminates when thermostatic switch on blanket
closes and begins to heat the blanket, at approximately 40
º
F.
Wiring Hook-up
12
Optional Accessory
Connection
3
2
1
Press Down The Center of the HotShot
Press Down The Center of the HotShot
9
1
2
3
P
art number HSPS150
Press Plugs T
ogether
To *****
Power Supply
To Optional
Accessory
Power Supply is for
Indoor Use ONLY!
Power Supply is for
Indoor Use ONLY!
Red LED indicates the power supply
is supplying power to heater blanket
26Vdc
®
SatelliteDish.com (954) 941-8883
The power supply is NOT water resistant, keep it indoor in a
dry location.
How The HotShot Works
ds/manuals/slimline/slimline 7 V4
Aug 14, 2018
Strip end of wire before
connecting to screws
Trim excess wire, do not leave coiled up
Use wire that is supplied with power supply.
