manualshive.com logo in svg

Hospira LifeCare XL Series, Техническое и сервисное руководство

Поделиться
Скачать
Hospira LifeCare XL Series Скачать руководство пользователя страница 60

5.4

BATTERY OPERATION OVERVIEW

Technical Service Manual

5 - 15

430-00587-008 (Rev. 2/05)

CAUTION:

As soon as the LOW BATTERY alarm occurs, connect the infusion system

to AC (mains) power.

Recharging occurs any time the infusion system is connected to AC (mains) power. It is
recommended that the infusion system be connected to AC (mains) power whenever
practicable to maximize available battery charge during transport or ambulation. The
power switch does not have to be on for the battery to recharge. Recharging while the
infusion system is operating is rate dependent.

Note:

The infusion system should be operated on battery power for six continuous

hours at least once every six months for optimum battery performance and life.

5.4.1

BATTERY CHARGER CURRENT TEST (OPTIONAL)

To perform the battery charger current test, refer to 

Figure 5-7, Battery Charger Current

Test Configuration

, then proceed as follows:

Note:

Make certain the battery is in good condition and charged. If necessary, use a

second battery for this test.

1. Disconnect the infusion system from AC (mains) power. Remove the battery access

cover and disconnect the battery. 

2. Connect the battery charger test circuit as illustrated in 

Figure 5-7

. Make certain

switch S1 is in the off position.

3. Connect the infusion system to AC (mains) power and allow 20 seconds for the

current to stabilize. Read the current on the current meter. 

4. Compare the measured current to the minimum and maximum values in 

Table 5-2,

Battery Charger Current Test Parameters

.

Note:

If the reading is too low, the battery may be fully charged. Close switch

S1; repeat Step 3 and verify per 

Table 5-2

.

5. Disconnect the infusion system from AC (mains) power. Remove the battery charger

test circuit. Reconnect the battery to the infusion system. Replace the battery access
cover and secure

.

Содержание LifeCare XL Series























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды