Hospira LifeCare XL Series Скачать руководство пользователя

Страница: 120 / 278

7.2

REPLACEMENT PROCEDURES

Technical Service Manual

7 - 41

430-00587-008 (Rev. 2/05)

7.2.9.4

OPENER HANDLE ASSEMBLY REPLACEMENT

The recommended tool for this procedure is a medium size flat blade screwdriver.

The replacement parts for this procedure are:

Ring, Retaining
Roller, Handle
Holder, Handle Spring
Spring, Torsion
Assembly, Opener/Handle

CAUTION:

Use proper ESD grounding techniques when handling components.

Wear an antistatic wrist strap and use an ESD-protected workstation. Store the PWA
in an antistatic bag before placing it on any surface.

To replace the opener handle assembly, refer to

Figure 7-23, Opener Handle Assembly

Replacement (1 of 3)

through

Figure 7-25, Opener Handle Assembly Replacement (3 of 3)

then proceed as follows:

1. Separate the front enclosure assembly, rear enclosure assembly, and main chassis

assembly as described in

Section 7.2.5

2. Remove the mechanism assembly as described in

Section 7.2.9.2

3. Lift the opener handle assembly. Open and disengage the cassette door. Close the

opener handle assembly.

4. Remove the retaining ring.

5. Insert the medium size flat blade screwdriver between the opener handle assembly

and the mechanism assembly. Carefully pry the assemblies apart. Remove the
handle roller from the backside of the opener handle assembly as the opener handle
is removed.



Note:

The handle spring holder and torsion spring may fall free.

6. Install the replacement opener handle assembly in the exact reverse order of

removal. Confirm that the shaft alignment dots are aligned

(see Figure 7-25)

7. Replace the mechanism assembly in the exact reverse order of removal.

8. Join the front enclosure assembly, rear enclosure assembly, and main chassis

assembly in the exact reverse order of separation.



Note:

(XLM with DataPort) When joining the front and rear enclosures, do not

pinch the DataPort/MCU cable between the two enclosures.

9. Connect the infusion system to AC (mains) power.

To verify successful opener handle assembly replacement, perform the PVT in

Section 5.2

Содержание LifeCare XL Series























































































































































































































































































Результаты поиска

Содержание LifeCare XL Series

Отзывы:

Похожие инструкции для LifeCare XL Series

Бренды по названию

Популярные бренды

Hospira LifeCare XL Series, Техническое и сервисное руководство

Результаты поиска

Содержание LifeCare XL Series

Отзывы:

Похожие инструкции для LifeCare XL Series

Бренды по названию

Популярные бренды