Hospira LifeCare XL Series Скачать руководство пользователя

Страница: 109 / 278

SECTION 7 REPLACEABLE PARTS AND REPAIRS

430-00587-008 (Rev. 2/05)

7 - 30

Plum XL Series

Figure 7-14.

XL Series Pole Clamp

7.2.8.11

POLE CLAMP SHAFT/KNOB ASSEMBLY AND POLE CLAMP
SHAFT TIP REPLACEMENT

The recommended tool for this procedure is wide-head pliers.

The replacement parts for this procedure are:

Assembly, Shaft/Knob, Pole Clamp
Tip, Shaft, Pole Clamp

To replace the pole clamp shaft/knob assembly and the pole clamp shaft tip, refer to

Figure 7-14

, then proceed as follows:

1. Turn the control knob to OFF/CHARGE.

2. Disconnect the infusion system from AC (mains) power.

3. Turn the pole clamp shaft/knob assembly counterclockwise to remove it from the

pole clamp extrusion and loosen the pole clamp shaft tip from the pole clamp/shaft
knob assembly.



Note:

The pole clamp shaft tip has a long shaft that is pressed into the

threaded pole clamp shaft/knob assembly.

04K01037

POLE CLAMP

BACKING PLATE

ADHESIVE BACKED

INSULATOR

10-32 x 1/2

HEX HEAD SCREW

WITH WASHER (2)

POLE CLAMP

EXTRUSION

POLE CLAMP

SHAFT/KNOB

ASSEMBLY

POLE CLAMP

SHAFT TIP

REAR ENCLOSURE

Содержание LifeCare XL Series























































































































































































































































































Результаты поиска

Содержание LifeCare XL Series

Отзывы:

Похожие инструкции для LifeCare XL Series

Бренды по названию

Популярные бренды

Hospira LifeCare XL Series, Техническое и сервисное руководство

Результаты поиска

Содержание LifeCare XL Series

Отзывы:

Похожие инструкции для LifeCare XL Series

Бренды по названию

Популярные бренды