background image

6

 

4. LOCATION 

  WARNING

This ice maker is not intended for outdoor use. 
This ice maker should not be located next to ovens, grills or other high heat producing equipment. 
This appliance is not suitable for installation in an area where a water jet could be used.

 

  CAUTION

The location should provide a firm and level foundation for the icemaker.

 

NOTICE

Do not place anything on top of the icemaker or in front of louver.

 

IMPORTANT

Normal operating ambient temperature should be within 5℃  to 38℃. Normal operating water temperature should be within 
5℃  to 32℃. Operation of the icemaker, for extended periods, outside these normal temperature ranges may affect production 
capacity and life. 
Allow the clearance specified below for proper air circulation and ease of maintenance and/or service should they be required

.

 

 

 

 

 

 

 

NOTE: SRM-45A:L=1cm; SRM-60/80/105/125A: L=15cm.

 

In some high humidity environments, condensation may from inside the machine and drip onto the floor. Do not install where 
the floor can be affected by water. 

5. INSTALLATION 

  CAUTION

Incorrect installation can cause harm to people, animals or other items, for which the manufacturer cannot be held 
responsible. 

 

*Place the icemaker in selected permanent site

*When attaching the adjustable lets / nuts (accessory)

level the unit in both the left-to-right and

 

front-to-rear directions

 

 

                                                                                                           

[SRM-45A]                                                [SRM-60/80/105/125A] 

6. ELECTRICAL CONNECTIONS 

  WARNING

THIS APPLIANCE MUST BE EARTHED 

This icemaker requires an earth that meets the national and local electrical code requirements. 
To prevent possible severe electrical shock to individuals or extensive damage to the unit, install a proper earth wire to the 
icemaker. 
Disconnect the main power supply before any maintenance, requires or cleaning is undertaken. 

*This series of icemaker require a separate power supply (220VAC/10A). The electrical supply must be protected by a suitable 

circuit breaker. 

*The main control box fuse is rated at 5A and should be replaced by a qualified service engineer. 

 

Ice maker 

15cm

 

15cm

 

0

 

cm

 

Rear 

Right

Left 

Front 

Top View 

 

Ice 

maker 

L

cm

 

0

 

cm

 

Top

Rear 

Adjustable 
Leg 

Side View 

Adjustable 
Nut 

Содержание SRM-105A


















Отзывы: