manualshive.com logo in svg

Hoshizaki RELIABILITY IS A BEAUTIFUL THING DCM-270BAH-OS, Руководство по обслуживанию

Поделиться
Скачать
Hoshizaki RELIABILITY IS A BEAUTIFUL THING DCM-270BAH-OS Скачать руководство пользователя страница 24

24

If you experience problems with the ice or water dispense, use the following charts along
with the wiring diagram (section III, 3) to guide you through your troubleshooting.

The following tables show the proper voltage readings for each operation.

Water Dispensing

Ice Dispensing in Continuous Mode

Ice Dispensing in Portion Controlled Mode

Layout of Portion Control Switch Wiring

(Front of Machine)

Lead 1 

Lead 2 

Dispense  Non-Dispense 

K2 PIN 6 

(LBU) 

to GND 

or

 NEUTRAL

120 VAC 

0 VAC 

K5 PIN 4 

(W/O) 

or

(RED) on 

sensor 

to  K5 PIN 5 (Y) 

or

 (WH) on 

sensor 

5 VDC 

0 VDC 

K5 PIN 4 

(W/O)

 or

(RED) on 

sensor 

to K5 

PIN 

6 

(W/BR) 

or

 (BK) on 

sensor 

5 VDC 

5 VDC 

Lead 1 

Lead 2  Dispense Non-Dispense 

K2 PIN 8 

(DBU) 

to K4 PIN 2 

(LBU) 

24 VAC 

0 VAC 

K5 PIN 7 

(RED) 

to K5 PIN 9 

(BK) 

5 VDC 

5 VDC 

K5 PIN 7 

(RED) 

to K5 PIN 8 

(WH) 

5 VDC 

0 VDC 

The K2 connector supplies voltage to the ice and water dispense motors and solenoids
through pins 4, 6, 8. The K2 connector also has the gear motor protect circuit on pins 1, 2
the flush valve circuit on pins 9, 10 and voltage inputs on pins 3, 5, 7.
The K5 connector is used exclusively for the input and output signals for the optical sensors.

Lead 1 

Lead 2 

Dispense  Non-Dispense 

K2 PIN 6 

(LBU) 

to

GND 

or 

NEUTRAL 

120 VAC 

0 VAC 

K5 PIN 1 

(W/R) 

or

(RED) on 

sensor 

to

K5 PIN 3 

(W/BK) 

or

(BK) on 

sensor 

5 VDC 

5 VDC 

K5 PIN 1 

(W/R) 

or

(RED) on 

sensor 

to

K5 PIN 2 

(W/BL) 

or

(WH) on 

sensor 

5 VDC 

0 VDC 

Содержание RELIABILITY IS A BEAUTIFUL THING DCM-270BAH-OS















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды