background image

3

Important Safety Information

Throughout this manual, notices appear to bring your attention to situations which could
result in death, serious injury, damage to the appliance, or damage to property.

WARNING

 

Indicates a hazardous situation which could result in death or 

serious injury.

NOTICE

 

Indicates a situation which could result in damage to the 
appliance or property.

IMPORTANT

 

Indicates important information about the installation, use, and 
care of the appliance.

WARNING

The appliance should be destined only to the use for which it has been expressly 
conceived. Any other use should be considered improper and therefore dangerous. 
The manufacturer cannot be held responsible for injury or damage resulting from 
improper, incorrect, and unreasonable use. Failure to install, operate, and maintain 
the appliance in accordance with this manual will adversely affect safety, performance, 
component life, and warranty coverage and may result in costly water damage.

To reduce the risk of death, electric shock, serious injury, or fi re, follow basic 
precautions including the following:

• Only qualifi ed service technicians should install and service the appliance.
• The appliance must be installed in accordance with applicable national, state, and 

local codes and regulations.

• The appliance requires an independent power supply of proper capacity. See the 

nameplate for electrical specifi cations. Failure to use an independent power supply of 
proper capacity can result in a tripped breaker, blown fuse, damage to existing wiring, 
or component failure. This could lead to heat generation or fi re.

• 

THE APPLIANCE MUST BE GROUNDED:

 The appliance is equipped with a NEMA 

5-15 three-prong grounding plug to reduce the risk of potential shock hazards. It must 
be plugged into a properly grounded, independent 3-prong wall outlet. If the outlet 
is a 2-prong outlet, it is your personal responsibility to have a qualifi ed  electrician 
replace it with a properly grounded, independent 3-prong wall outlet. Do not remove 
the ground prong from the power cord and do not use an adapter plug. Failure to 
properly ground the appliance could result in death or serious injury.

• Do not use an extension cord.
• To reduce the risk of electric shock, do not touch the control switch or plug with damp 

hands. Make sure the control switch is in the “OFF” position before plugging in or 
unplugging the appliance.

• Do not use an appliance with a damaged power cord. The power cord should not 

be altered, jerked, bundled, weighed down, pinched, or tangled. Such actions could 
result in electric shock or fi re. To unplug the appliance, be sure to pull the plug, not 
the cord, and do not jerk the cord.

• Do not make any alterations to the appliance. Alterations could result in electric 

shock, injury, fi re, or damage to the appliance.

Содержание KM-61BAH





























Отзывы: