background image

70

D. Descaling (As Required)

Use a descaler according to the supplier’s instructions.

     WARNING

1. Carefully follow any instructions provided with the descaler.
2. Always wear liquid-proof gloves and goggles to prevent the descaler from 

coming into contact with skin or eyes.

3. To prevent generation of toxic chlorine gas, do not mix a descaler with a 

chlorinated cleaner.

1) Pull out the drain pipe to drain water from the wash tank. Start the auto 

fi

 ll cycle to 

fi

 ll 

the wash tank with hot water.

2) Use the “ON/OFF” button to turn off the unit. Refer to the descaler's directions and add 

the proper amount of descaler to the wash tank. The wash tank holds 26.4 gallons of 
water.

3) Press and hold the up and down buttons and the “CHANGE” button, then press the “ON/

OFF” button to select the “PC” (Preventative Cleaning) mode.

4) Refer to the descaler's directions for the proper duration of cleaning. When the proper 

amount of time has passed, press the “ON/OFF” button to stop cleaning.

5) Check the wash tank interior. Repeat steps 1) through 4) if necessary.

     WARNING

Be careful not to burn yourself with the hot water or parts in the wash tank.

6) Drain the wash tank, then start the auto 

fi

 ll cycle. Run the dishwasher to rinse the wash 

tank thoroughly. Drain the wash tank.

E. Shutdown

NOTICE

If there is a possibility that the 
ambient temperature may fall below 
32°F (0°C) and freeze the unit, be 
sure to drain the unit. The water 
supply line could be damaged and 
leak water, resulting in damage to 
the surrounding property.

To drain out the water heater, close 
the water supply line shut-off valve, 
and open the drain valve and water 
supply valve.

Water Heater

Gas Supply Line 

Shut-off Valve

Water Supply Line 

Shut-off Valve

Booster Tank

Water Supply Valve

Drain Valve

Dishwasher

Содержание JWE-2400CUA-L-25B
















































































Отзывы: