MAN0979-01-EN_XHSQ_XHSQ-5_Datasheet
Specifications / Installation
©Horner APG, LLC. No part of this publication may be reproduced without the prior agreement and written permission of Horner APG, LLC. Information in this document is subject to change without notice.
8/28/2013
3.
INSTALLATION
Observe the following procedure to install the option module:
1.
Disconnect all connectors from the X-Series unit including power.
2.
Remove the four screws on the back of the X-Series unit and remove the back cover. The back cover will be replaced with the extended back cover
that ships with the I/O add-on. Screws are re-used (Figure 1).
3.
Plug the HSQ module onto the 24-pin connector. Ensure that all the pins are properly aligned (Figure 2).
4.
Place the extended back cover onto the unit. It can be helpful to tip it at an angle so the connector on the module passes through the opening in the
back cover.
5.
Place the screws back into the hole and turn the screw slowly counter clockwise until it clicks into the threads. This prevents the screw from being
cross-threaded. Turn the screw clock-wise until the cover is firmly secured. Repeat this process for all four (4) screws. Do not tighten the screws to
more than 0.4Nm
NOTE:
When using this module with an HE-XE104, HE-XE105, or similar XL models with a 13 pin bottom I/O connector, the add-on module connector
interferes with the stock I/O board connector. It is necessary to order a replacement I/O connector available as part number HE-XKIT45. This is not necessary
for the 102 and 103 style XL units.
Note: XLE used as an example, the procedure is applicable to all XL-Series
4.
INSTALLATION / SAFETY
When found on the product, the following symbols specify:
WARNING:
To avoid the risk of electric shock or burns, always connect the safety (or earth) ground before making any other connections.
WARNING:
To reduce the risk of fire, electrical shock, or physical injury it is strongly recommended to fuse the voltage measurement inputs. Be sure to locate fuses as close to the source as possible.
WARNING:
Replace fuse with the same type and rating to provide protection against risk of fire and shock hazards.
WARNING:
In the event of repeated failure, do not replace the fuse again as a repeated failure indicates a defective condition that will not clear by replacing the fuse.
WARNING:
Only qualified electrical personnel familiar with the construction and operation of this equipment and the hazards involved should install, adjust, operate, or service this equipment. Read and
understand this manual and other applicable manuals in their entirety before proceeding. Failure to observe this precaution could result in severe bodily injury or loss of life.
All applicable codes and standards must be followed during the installation of this product. Adhere to the following safety precautions whenever any type of connection is made to the module:
•
Connect the safety (earth) ground on the power connector first before making any
other connections.
•
When connecting to electric circuits or pulse-initiating equipment, open their related
breakers.
•
Do not make connections to live power lines.
•
Make connections to the module first; then connect to the circuit to be monitored.
•
Route power wires in a safe manner in accordance with good practice and local codes.
•
Wear proper personal protective equipment including safety glasses and insulated
gloves when making connections to power circuits.
•
Ensure hands, shoes, and floors a r e dry before making any connection to a power
line.
•
Make sure the unit is turned OFF before making connection to terminals.
•
Make sure all circuits are de-energized before making connections.
•
Before each use, inspect all cables for breaks or cracks in the insulation. Replace
immediately if defective
5.
TECHNICAL SUPPORT
For assistance and manual updates, contact Technical Support at the following locations:
NORTH AMERICA
(P) 317-916-4274, (F) 317-639-4279
Web:
Email:
EUROPE
(P) +353-21-4321266, (F) +353-21-4321826
Web:
Email:
Warning:
Electrical Shock Hazard.
Warning:
Consult user documentation.
