HORNER HE800PCU100 Скачать руководство пользователя страница 2

Страница: 2 / 10

PAGE 2

19 APR 2005

MAN0790-01

2.2

Equipment Setup / Network

•

Interaction with the PCU100 (PCU) requires a

OCS

. Although the PCU does not have a local

operator interface, it does support a remote operator interface through an OCS over a

CsCAN

network.

•

As shown in

Figure 1

, the PCU is connected to a Hewlett Packard (HP) printer with the cable that

comes with the PCU. The cable connects the PCU to

any Hewlett-Packard printer

with IEEE

1284 parallel port and that uses PCL3 or greater.

Note:

Our example uses one PCU, but multiple PCUs can be connected to the CsCAN network.

Figure 1 - PCU Setup in a CsCAN Network

2.3

Interface Configuration Software

Cscape

software is used to interface the PCU to the OCS over a

CsCAN network

2.4 Ladder

Programming

You need to build a ladder program (subroutine or sequence) that uses NETPUT and NETGET to
configure and control the PCU. Examples of ladder code programs are shown in

Figures 3 through 6.

Also, refer to

Tables 1 through 2

OCS

Controller

PCU100

HP Printer

Configured over
CsCAN Network

Cable

(Sent with PCU.)

-Configure with
Cscape Software.
-Program with Ladder
Code.

Содержание HE800PCU100











Результаты поиска

Содержание HE800PCU100

Отзывы:

Похожие инструкции для HE800PCU100

Бренды по названию

Популярные бренды

HORNER HE800PCU100, Конфигурация

Результаты поиска

Содержание HE800PCU100

Отзывы:

Похожие инструкции для HE800PCU100

Бренды по названию

Популярные бренды