HORNER HE800PCU100 Скачать руководство пользователя страница 1

Страница: 1 / 10

MAN0790-01

19 APR 2005

PAGE 1

For PCU100 (PCU) specifications and installation information, refer to datasheet (

MAN0432

). See

Technical Support

section in this document for manual updates and assistance.

1 Product

Overview

The Printer Control Unit (PCU100)…

•

Is a

low cost solution

that allows you to

collect, store and track data

(up to

hours) and

print

data Trend Reports

without costly HMI units or chart recorders.

•

Comes

conveniently pre-programmed

to record and print

four standard types of data trend

measurements

that are commonly used in business and industry:

Pressure, Flow Rate,

Temperature

and

Level

trends.

•

Allows

fast, easy

creation of

OCS interface

using

pre-programmed controls

•

Connects to any Hewlett-Packard printer

with IEEE 1284 parallel port and that uses PCL3

such as HP Deskjet 5650.

•

Provides

customized reports

such as alarm or industry-specific reports - available for additional

cost by contacting Horner Sales staff.

An example of a data trend report is on the last page of this document

2 Configuration

Overview

2.1

Brief Summary of Steps to be Taken

The following steps must be done to configure the PCU. They are covered

in detail

later in this section.

Setup equipment including the PCU, Hewlett Packard printer, cable, and Master Controller (Horner

Operator Control Station [

OCS

] in our example).

Configure the OCS to interface with the PCU via the

CsCAN network

Build a

ladder program

in the OCS to interface to and control the PCU.

Printer Control Unit

HE800PCU100

Configuration

Содержание HE800PCU100











Результаты поиска

Содержание HE800PCU100

Отзывы:

Похожие инструкции для HE800PCU100

Бренды по названию

Популярные бренды

HORNER HE800PCU100, Конфигурация

Результаты поиска

Содержание HE800PCU100

Отзывы:

Похожие инструкции для HE800PCU100

Бренды по названию

Популярные бренды