background image

3

ZIPPER II INSTRUCTION MANUAL

Electrical safety

Warning

: to reduce the risk of fire or electric shock, do not expose this 

appliance to rain or moisture.

Caution

: to reduce the risk of electric shock, do not attempt to open 

the plastic casing of this machine. The machine carries dangerously 

high voltages inside even when switched off and disconnected from 

the electrical socket. There are no user-serviceable parts inside. Refer 

servicing to qualified service personnel.
•  Use only on a 220-240 volt AC 50 Hz electricity supply.
•  Use a Circuit Breaker (RCD) with this machine.
•  Use a 

3 amp

 fuse in the plug.

•  Never insert the plug into a damaged socket.
•  Keep the electric lead up, out of the way of animals.
•  Switch off and unplug the machine before changing the comb or cutter 

and before any maintenance.

•  Never use the machine if you suspect it of having been in contact with 

liquids.

•  Check the machine body and electrical cable for defects before use.

Sacrificial gear safety feature

This machine incorporates a sacrificial gear which is designed to strip in 

the event of the machine jamming or encountering an obstruction, e.g. 

wire in wool, improper comb setup (see page 5) or lack of oiling.

Содержание Zipper II









Отзывы: