background image

4

Battery Power Mode

When the RAPiD

®

 Safe is unplugged, 

and is operating on battery power, 

you 

must press any button on the keypad 
to activate the reader. 

Pressing any button on the keypad 

causes the system to go from battery 

saving mode to ready status.

For example:

 To open your vault 

with an RFID tag, while the system is 

running on battery power, first press 

any

 

button on the keypad to bring it 

to ready status. Place your RFID tag 

within 1" of the center of the RFID 

reader to open the vault.

Batteries 

To install batteries, open door with barrel keys and locate battery compartment on the back 
of the door.  Remove battery cover and insert four (4) high quality AA batteries. Replace all 
batteries at the same time. 

To check battery level:

1. Disconnect from AC power source. 
2.  Press and release “H” button on the 

keypad.

3.  The LED light on the “H” button will flash.
  a. Flashing Green – Good battery
  b. Flashing Yellow –  Low battery
  c. Flashing Red – Dead battery

4.  After 10 seconds the vault will return to 

normal operation.

NOTE:  

Replace batteries every twelve 

months or as needed.

RFID Reader  

& Key Pad

“H” Button

Lock Tabs

Содержание RAPiD SAFE READY VAULT













Отзывы: