Horizon Hobby LOSB0126 Скачать руководство пользователя страница 7

7

About the Radio

The Spektrum

 DX3S radio installed in the Ten-T is a 

professional level system with more than the usual features 

you may find useful. Be sure to read through the included 

radio manual for complete instructions. The following is a 

simple guide referring to items that are commonly used and/or 

needed to run your model.

1

2

3

5

4

8

6

9

7

1.  Power Switch - Turns your transmitter ON and OFF

2.  Steering Wheel - Controls the steering of your model

3.   Steering Trim Tab - Allows you to fine-tune the neutral 

position of the steering

4.   Throttle Trigger - Pull back for throttle and push forward 

for brakes

5.   Throttle Trim Tab - Allows you to set the idle/brake of the 

model

6.   Transmitter Display - Digital readout shows battery 

voltage, temperature, rpm/speed and functions/settings

7.   Transmitter Antenna - Transmits signal to the receiver in 

the model

8.   AUX - Lever for forward/reverse

9.  Starter button

Radio Operation

It is important that you familiarize yourself with the radio 

system, as this is your direct link to the model.

• 

Never run your model with low receiver or transmitter 

batteries.

• 

Always fold the antenna to the upright position before 

running your model.

• 

Never leave the power on or the batteries will not last 

long.

• 

Always turn the transmitter ON before turning the model 

ON.

• 

When finished running, always turn the model OFF before 

the transmitter.

• 

For best operation, it will be necessary to keep the “trims” 

adjusted for both the steering and throttle as noted on the 

following pages.

Steering Trim

: The model should go straight without turning 

the steering wheel. If not, tap the trim lever found just above 

and to the right of the steering wheel in the direction needed 

for the model to go straight. Each tap of the trim button will be 

accompanied by an audible tone indicating a change has been 

made. It may take several taps to get the correct trim setting.

Throttle Trim

: The model should idle without the tires 

rotating when the trigger is at its neutral position. If not, tap the 

trim lever found just above and to the left of the steering wheel 

to reposition the throttle servo and close the carburetor and 

apply more brakes. Note that additional braking force is applied 

when you push the trigger forward.

Содержание LOSB0126



























Отзывы: