background image

EN

CAUTION:

 Elevon mixing is automatically applied by the AR636 

receiver. If you are using the BNF version of this aircraft, you must 

set the Wing Type to 1 AIL. Changing the Wing Type to any other setting 

will cause loss of control of the aircraft. 

4

F-27D Evolution

Preflight

Transmitter Setup (BNF only)

IMPORTANT:

 After you set up your model, always rebind the transmitter and 

receiver to set the desired failsafe positions. 

Dual Rates

Take first flights in Low Rate. For landings, use high rate elevator.

NOTICE:

 To ensure AS3X

®

 technology functions properly, do not lower rate 

values below 50%. If lower rates are desired, manually adjust the position of 

the pushrods on the servo arm.

NOTICE:

 If oscillation occurs at high speed, refer to the Troubleshooting 

Guide for more information.

Expo

After first flights, you may adjust expo in your transmitter.

Computerized Transmitter Setup 

Start all transmitter programming with a blank ACRO model (perform a 

model reset), then name the model. 

Set Dual Rates to

HIGH 100% 
LOW 70%

Set Servo Travel to

100% 

Set Servo Expo to 

HIGH RATES 30%
LOW RATE

DXe

Refer to spektrumrc.com for the appropriate download setup.

DX6i

1. Go to the SETUP LIST MENU
2. Set MODEL TYPE: ACRO

DX7S
DX8

1. Go to the SYSTEM SETUP
2. Set MODEL TYPE: AIRPLANE 
3. Set WING TYPE: 1 AIL

DX6e
DX6 (Gen2)
DX7 (Gen2)
DX8 (Gen2)
DX9
DX10t
DX18
DX20

1. Go to the SYSTEM SETUP

2. Set MODEL TYPE: AIRPLANE 

3. Set AICRAFT TYPE:  

 

WING: 1 AIL

SAFE

®

 Select Technology (BNF only)

The evolutionary SAFE

®

 Select technology can offer an extra level of protection so you can perform the first flight with confidence. No complex transmitter 

programming is required. Just follow the simple bind process to make the SAFE Select system active. When activated, bank and pitch limitations keep you from 

over-controlling and automatic self-leveling makes recovery from risky or confusing attitudes as simple as releasing the sticks. In fact, with the aileron, elevator 

and rudder sticks in the neutral position, SAFE Select will automatically keep the airplane in a straight and level attitude. 
Expand the advantage of what SAFE

®

 Select technology offers by assigning it to a switch. No transmitter programming is required and you’ll be able to turn 

the system ON and OFF with the flip of a switch. For example, turn SAFE select ON for takeoffs to counter the torque of the propeller. Turn it OFF in flight for 

unrestricted aerobatic performance, and turn it back ON when a buddy wants to try out your cool aircraft.  Turn SAFE Select ON for landings. It will help keep the 

correct pitch attitude and wings level during the final approach. Whether you’re a beginner or an expert, SAFE Select can make your flights a great experience.
When the normal bind process is followed, the SAFE Select system is disabled, leaving specially tuned AS3X

®

 technology in place to deliver a pure, unrestricted 

flight experience.

1.  Remove and inspect contents.
2.  Read this instruction manual thoroughly.
3.  Charge the flight battery.
4.  Setup Transmitter using transmitter setup chart.
5.  Fully assemble the airplane. 
6.  Install the flight battery in the aircraft (once it has been fully charged).
7.  Check the Center of Gravity (CG).
8.  Bind the aircraft to your transmitter.

9.  Make sure linkages move freely.
10. Perform the Control Direction Test with the transmitter.
11. Perform the AS3X Control Direction Test with the aircraft.
12. Adjust flight controls and transmitter.
13. Perform a radio system Range Test.
14. Find a safe open area to fly.
15. Plan flight for flying field conditions.

Содержание F-27D Evolution




















Отзывы: