Horizon Fitness PC-S43 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 20

Horizon Fitness PC-S43 Скачать руководство пользователя страница 1

I

Important Information

- This manual is designed to help you to install, operate and maintain the PC-S43 Paper

Cutter. Please read and understand this manual and keep it in a safe and convenient place.

- Do not operate the PC-S43 until you read and understand the instructions in this manual.

- Horizon International Inc. shall not be liable for incidental consequential damages result-

ing from: improper or inadequate maintenance by customer, unauthorized modification or
misuse, or operation outside of the environmental specifications for the product.

- Horizon International Inc. pursues a policy of continuing improvement in design and

performance of the product. Therefore, the product design and specifications are subject to
change without prior notice and without our legal obligation.

- All rights are reserved. No part of this manual may be photocopied, reproduced or trans-

lated to another language without the prior written consent of Horizon International Inc.

PC-S43

(inch)

PAPER CUTTER

UM204017-00

031031/PCS43inch/00E/HS

1
2
3
...
»

Содержание PC-S43





















Отзывы:

Нет отзывов