hopf 8029NTS-V2/GPS Скачать руководство пользователя

Страница: 57 / 121

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

57 / 121

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

7.3.3.4 Server Configuration

The basic settings for NTP base functionality are displayed selecting

the “Server

Configuration” link.

The NTP-hopf-

refclock driver is already configured as standard (127.127.38.0 in the “Peers

Summary”) and is not explicitly displayed here.

7.3.3.4.1 Synchronization Source (General / Synchronization source)

"Synchronization source"

either GPS or DCF77, depending on the appropriate Sync

Source, has to be selected. This is reuiqred in order to align the NTP algorithm for the
calculation of the accuracy with the synchronization source.

Based on the selection of GPS, even though GPS is not the source of the
Sync Source (different product option) the value

HIGH

for

Accuracy

may

never be reached.

7.3.3.4.2 NTP Syslog Messages (General / Log NTP Messages to Syslog)

This option enables or disables Syslog messages which are generated from the NTP service.

This value has no effect if Syslog is not configured in the ALARM tab (see

Chapter 7.3.4.1

Syslog Configuration

Содержание 8029NTS-V2/GPS


























































































































Результаты поиска

Содержание 8029NTS-V2/GPS

Отзывы:

Похожие инструкции для 8029NTS-V2/GPS

Бренды по названию

Популярные бренды

hopf 8029NTS-V2/GPS, Техническое руководство

Результаты поиска

Содержание 8029NTS-V2/GPS

Отзывы:

Похожие инструкции для 8029NTS-V2/GPS

Бренды по названию

Популярные бренды