5
2.1
Cleaner description
Operate cleaner only at voltage specified on
data plate on bottom of cleaner.
The assembled cleaner will look like the
drawing .
1 . Handle
2 . Custom Control™ powerswitch
3 . Custom Control™ indicator
4 . Tool cover
5 . Dusting brush
6 . Powered hand tool
7 . Furniture nozzle
8 . Dirt cup
9 . Dirt cup handle
10 . HEPA cartridge filter
11 . Pre-filter
12 . Final filter
13 . Three position handle release pedal: step
on lever to lower handle to operating or
low positions .
14 . Nozzle control knob: rotate knob to
correct setting for height of carpet
being cleaned .
15 . Furniture guard
16 . Headlight
17 . Hose
18 . Hose holder
19 . Cord hooks: wrap cord around hooks for
storage . The top hook rotates right or
left for easy cord release .
20. Extension wand
21 . Crevice wand: stores in wand .
*some models only.
This cleaner is intended for household use.
Not intended for commercial use in any
household or for any other commercial
purpose.
1
2
3
4
5
11
10
16
15
14
12
6
7
8
9
17
21
20
19
13
17
18
Polarized plug
To reduce the risk of electric shock, this appli-
ance has a polarized plug (one blade is wider
than the other) . This plug will fit in a polar-
ized outlet only one way . If the plug does not
fit fully in the outlet, reverse the plug . If it
still does not fit, contact a qualified electrician
to install the proper outlet . Do not change the
plug in any way .
2. HOW TO USE
16
A
Disconnect cleaner from electrical outlet.
Low suction or pick up may be due to a
blockage in the system . Refer to the follow-
ing steps to check for blockages continuing
with each step until the blockage is found:
A . If a blockage occurs during floor cleaning:
Turn cleaner OFF and disconnect from elec-
trical outlet .
1 . Check fullness of dirt cup and filter
assembly; empty cup and clean filters if
needed .
4.1
Check dirt duct
2 . Remove dirt cup,
look in duct (A) .
3 . Clear blockage
from dirt duct .
4.2
Check brushroll
4 .
Turn cleaner OFF
and unplug.
5 . Turn cleaner over
and clear block-
age from brushroll .
Return cleaner to
operating position .
Turn cleaner back
on and continue
cleaning .
Clearing blockages
4.3
Check hose tube
6 .
Turn cleaner OFF
and unplug.
7 . Remove hose
from tube . Clear
blockage from
tube . Also, check
hose for blockage .
PROBLEM
POSSIBLE CAUSE
POSSIBLE SOLUTION
Cleaner hard to
push
Incorrect carpet height
setting
Move nozzle control knob to a higher
setting
Broken or worn belt
Replace belt
Cleaning tools
won’t pick up
Blockage in hose
Clear blockage .
Visible dirt
leaking through
final filter
Filter assembly not installed
properly
Remove filter assembly from dirt cup
and ensure that HEPA cartridge filter is
properly attached to pre-filter screen and
that entire filter assembly is properly repo-
sitioned inside dirt cup . (Figs . 3 .6 through
3 .11) .
Dirt inside dirt
cup stops
spinning
Note: Heavy debris may settle to the
bottom of the dirt cup and prevent the dirt
from spinning without affecting cleaning
performance . The cleaner can continue
to be used even if the dirt is not spinning
inside the dirt cup .
However, if the dirt does stop spinning
AND there is a noticeable decrease of
performance, check the items under
“Cleaner won’t pick up”.
Powered hand
tool brushroll
won’t turn
Too much pressure being
applied to tool
Continue using tool applying light
Blockage in turbine channel Remove blockage .
Broken or worn belt Replace belt
Low cleaner suction
Check items under “Cleaner won’t pick up”.
Actual model may vary from images shown.
Actual model may vary from images shown.
