Extra Load Button
(Dodatkowy za∏adunek)
This option can only be utilised for cotton programmes. Hoover has designed a special wash
boost system specially for big loads - by selecting this option button, the volume of water
within the selected wash cycle and the length of time of the programme is increased to
improve the wash performance for the bigger load.
Express Wash button
(Pranie Ekspresowe)
This option can be utilised on cotton and synthetic programmes. By selecting the express
wash option, the wash time may be reduced by up to 50 minutes, depending on the
programme selected.
Pre-Wash button
(Pranie Wst´pne)
This option is particularly useful for heavily soiled loads and can be used before selecting the
main wash programme. Detergent for this programme should be added to the first
compartment of the soap drawer labelled “I” (Please refer to Detergent Drawer Section of
manual). We recommend you use only 20% of the recommended quantities shown on the
detergent pack and fabric conditioner should not be used for this programme.
Extra Rinse Button
(Ekstra p∏ukanie)
This option adds more water at the rinsing stage. This can help prevent skin irritation from
detergent residue for people with particularly sensitive skin. Selecting the Extra rinse button is
also recommended when washing heavily soiled fabrics which needs a lot of detergent, or
when the wash load contains towelling fabrics that have a greater tendency to retain
detergent.
Select Spin
(Pr´dkoéç wirówki)
On selecting the wash programme the display will inform you of the maximum spin speed
permitted for that programme. By repeatedly pressing the select spin button the speed will
decrease by increments of 100 rpm. The minimum speed permitted is 400 rpm, or by
continuously pressing the select spin option the spin may be cancelled if desired.
On selecting the required spin speed the display will then inform you of the chosen
programme, its temperature and the newly selected spin speed.
Programme Lock
(Blokada programu)
This is a useful feature to prevent children playing with the option buttons and tampering
with the programme you have set.
After you have set the programme and option buttons you require, press start
and then programme lock. This “locks” the control panel.
You may cancel this function by pressing the programme lock button briefly until you see the
light above the button flash. While this light is flashing, press the “Fast Iron” (Szybkie
prasowania) button – the display will inform you that the options are no longer locked and
further changes can now be made.
Set Programme End Time
/Delay start
(Koniec programu/Opóêniewie Startu)
The programme end time/delay start options can be used if you want the washing to be ready
at a later time (but within 24 hours).
Start/Pause Button (
Start/Pauza)
START
To start a programme press this button once. The door locked light will illuminate.
The machine will now be sensing the wash load and ask you to please wait.
Example
The Inter@ct panel will then display the time to complete the programme and then the wash
cycle will commence. Inter@ct calculates the time to the end of the selected programme
based upon a standard 4,5 Kg load, during the cycle, Inter@ct corrects the time to that
applicable to the size and composition of the load.
Example
This display also shows the current phase of the cycle (eg, Currently in cold prewash) and in
the bottom right hand corner, the current time is displayed.
This display will change throughout the wash programme as the cycle develops.
PAUSE
The programme may be paused at any time during the wash cycle by holding down the
Start/Pause button for about two seconds and a beep will sound. A message will appear on
the display to inform you that the programme has been paused. To restart the programme
press the Start/Pause button once again. The display will inform you that the programme will
continue.
Example
SETTING WASHING
PARAMETERS: PLS WAIT
TIME TO END 1H:50M
COLD PREWASH 19:30
COLOURFAST COTTON
PROGRAMME PAUSED
PROGRAMME CANCELLED
Door open button (
drzwi)
:
A special safety device prevents the door from being
operated immediately after the end of the cycle. “Door locked” indicator light is
illuminated when the door is fully closed. Wait for 2 minutes after the wash cycle has
finished before opening the door. The door locked neon will go out and the door may be
opened. As a safety measure check that there is not water evident in the drum.
CANCEL
To cancel the programme the Start/Pause button must be pressed down for 5 seconds until the
beep sounds. The display will inform you that the display has been paused and has then been
cancelled.
Example
45
44
