background image

2.  Be sure you start from the outside of the door with the Outside Section 

of the lock and feed cable to the inside through the second hole from the 

bottom. 

3.  EXTEND the deadbolt. Start feeding the two bolts near the bottom of 

the lock through the two respective holes in the door.    When started, 

start jiggling the lock into the door while positioning the loose torque 

bar at the deadbolt end of the lock so it slips 

HORIZONTALLY

 into 

the deadbolt gear screw. 

4.  Work the unit until it is flush against the door with the rubber gasket 

aligned perfectly around the lock, then hold in place so it doesn’t slip 

out.

Shepherd 210A Installation Manual V1.1

©

©Copyright 2004. Hongda USA Inc.

14

Fig 8 

Fig 9 

4.4 Mounting the Plat to Fix Outside Section onto Door 

Position the Plate taken off earlier from the Inside Section (Fig. 5) on the inside 

of the door with the two tabs at the top and sticking out.    Use two 

B

 screws 

(slightly shorter of the four long pinch screws supplied) for mounting through 

the two holes near the top of the lock.    Screw in tightly making sure rubber 

gasket is positioned evenly around lock. 

Содержание DL210
















Отзывы: