比例/
scale
:
1
:
6
Z01
有机玻璃(透明)
plexiglass(transparent)
14
*
11.5
*
0
.
15
(
1
块/
piece
)
比例/
scale
:
1
:
6
Z02
有机玻璃(透明)
plexiglass(transparent)
11.5
*
10.85
*
0
.
15
(
1
块/
piece
)
比例/
scale
:
1:6
Z03
有机玻璃(透明)
plexiglass(transparent)
14.5*11.5
*
0
.
15
(
1
块/
piece
)
防尘罩/
Dust
cover
(升级版配件,需要另行购买/
Upgrade version
accessories
need to be purchased
separately
)
Z01
Z02
将
Z01
和
Z02
粘贴在
Z03
上
Z03
1
2
5
6
3
4
Z03
A
B
牛皮纸已撕掉的那一面朝内，
牛皮纸未撕掉的那一面朝外。
将
Z01
靠左边与
Z03
成
90
度直角。
(此面牛皮纸
已撕,朝上)
A
B
用
E03
来固定两块有机玻璃的交接处，
(可用透明胶带替代
E03
)
在两块玻璃的接口处涂上适量胶水并稍微用力刮一下
使胶水渗透进两块玻璃连接处 (画红线的地方为有机
玻璃接口)
Z03
Z02
Z01
Z03
每两块有机玻璃的交接处都需要用
E03固定（防止有机玻璃脱落）
Z01
(此面牛皮纸
未撕
,
朝外)
Z01
E03
E03
E03
E03
E03
Z01
Z02
E03
E03
(此面牛皮纸
未撕
,
朝外)
E03
(外部视图/
outside
view
)
(内部视图/
inside
view
)
(平面展示图/plane display drawing)
放置
1
个小时,待胶水干透后,
再将有机玻璃外面一层牛皮纸撕掉。
取出有机玻璃,将每一块有机玻璃
有文字的那面牛皮纸都撕掉
（撕一面牛皮纸，留一面牛皮纸）
防尘罩的制作
Installation of dust cover
stick Z01 and Z02 on Z03
Take out the plexiglass and
tear off the
kraft paper with text on
each piece of
plexiglass
Ripped one side of kraft paper,
leaving one side of kraft paper
(
This side of kraft
paper not torn,
facing outward)
(
This side of kraft
paper has been
torn,facing up)
The kraft paper that has been ripped off
faces inwards, and the kraft paper that
has not been ripped out faces out wards.
Place Z01 to the left at a right angle of
90 degrees to Z03
Use E03 to fix the junction of two pieces
of plexiglass, (use transparent tape to
replace E03)
The junction of every two pieces of plexiglass
needs to be fixed with E03 (to prevent the
plexiglass falling off)
(
This side of kraft
paper not torn,
facing outward)
stick appropriate amount of glue to the interface of
the
two
pieces
of
glass
and
scrape it slightly to
make
the
glue
penetrate
into
the
junction of
the
two
pieces
of
glass
(the
red
line
is
theplexiglass
interface)
Leave it for 1 hour. After the glue dries out,
tear off a layer of kraft paper outside the plexiglass.
7
拼装完毕后，应把说明书予以保留/The instruction manual should be keep,after assembled.
