Honeywell Youjie HH660 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 164

Honeywell Youjie HH660 Скачать руководство пользователя страница 32

2 - 16

Shift Lock

is used when you normally have the Shift Lock key on (not common to U.S. keyboards).

Automatic Caps Lock

is used if you change the Caps Lock key on and off. The software tracks and reflects if you have Caps

Lock on or off . This selection can only be used with systems that have an LED that notes the Caps Lock status (AT keyboards).

Autocaps via NumLock

bar code should be scanned in countries (e.g., Germany, France) where the Caps Lock key cannot be

used to toggle Caps Lock. The NumLock option works similarly to the regular Autocaps, but uses the NumLock key to retrieve
the current state of the Caps Lock.

Emulate External Keyboard

should be scanned if you do not have an external keyboard (IBM AT or equivalent).

Note: After scanning the Emulate External Keyboard bar code, you must power cycle your computer.

Keyboard Conversion

Alphabetic keyboard characters can be forced to be all upper case or all lowercase. So if you have the following bar code:
“abc569GK,” you can make the output “ABC569GK” by scanning

Convert All Characters to Upper Case

, or to “abc569gk” by

scanning

Convert All Characters to Lower Case

.

These settings override

Note: If your interface is a keyboard wedge, first scan the menu code for

Automatic Caps Lock

(page 2-16). Otherwise, your

output may not be as expected.

Default = Keyboard Conversion Off

.

Shift Lock

Automatic Caps Lock

Autocaps via NumLock

Emulate External Keyboard

* Keyboard Conversion Off

Convert All Characters

to Upper Case

Convert All Characters

to Lower Case

«
...
30
31
32
33
34
...
»

Содержание Youjie HH660





































































































































































Отзывы:

Нет отзывов