background image

INSTALLATION INSTRUCTIONS

34-00013EF-01

WT8840 
Trade Water Heater Controls

APPLICATION

The WT8840 Water Heater Control is designed for use 
in Standing Pilot applications using an immersion 
well for water temperature sensing. All models of 
WT8840 include an integrated NTC temperature 
sensor.

The WT8840 is powered from a thermopile heated by 
the standing pilot flame. CS8840 pilot assemblies are 
designed for use with this control.

The immersion well for sensing water temperature 
has matched NTC thermistor sensors. These sensors 
provide the fail-safe mechanism through which the 
WT8840 can provide both accurate water 
temperature control as well as water temperature 
limit (Temperature Cut-Out [TCO]) function.

SPECIFICATIONS

IMPORTANT

WT8840 controls provide direct replacement 
only.

Pressure Regulator: 

The outlet pressure regulator 

setting is shown on the product label.

Inlet Pressure Range:

See appliance rating plate for inlet pressure range 

recommendation. 

0.5 PSI (14.0 in. w.c.) maximum inlet pressure 

allowed for proper operation.

Body Pattern:

 90 degrees with 1/2 in. inlet and 

1/2 in. inverted flare outlet.

Mounting: 

Mounting in upright position only.

Control Input:

Voltage Minimum: 350 mV dc, open circuit.
Voltage Maximum: 850 mV dc, open circuit.

Capacity: 

See Table 1.

Regulation Range:

Natural Gas:
   Minimum: 30,000 Btuh.
   Maximum: 85,000 Btuh.

Ambient Temperature Range: 

32 to 150 °F 

(0 to 66 °C)

Operating Range: 

0 to 150 °F (-18 to 66 °C)*

*Valve will operate at 0°F (-18°C) but valve 

characteristics can not be guaranteed until 
ambient temperature reaches 32°F (0°C).

Storage Range: 

-40 to 150 °F (-40 to 66 °C)

Humidity: 

95% non-condensing at 104 °F (40 °C)

Approvals:

This device is certified by Canadian Standards 

Association (CSA) to the following standards:
ANSI Z21.20
ANSI Z21.23
ANSI Z21.78
ANSI Z21.87
CAN/CSA-C22.2 No. 199-M89
CAN1-6.6-M78
CSA 4.6
CSA 6.20

Accessory Parts:

Pilot Assembly CS8840

Trade Service Part

Replaces

WT8840A1000

WV8840A1000

WV8840A1001

WT8840A1500

WV8840A1050

WV8840A1051

WT8840B1000

WV8840B1042

WV8840B1109

WV8840B1110

WT8840B1500

WV8840B1059

WV8840B1117

WV8840B1118

Содержание WT8840









Отзывы: