Honeywell W4-IC Скачать руководство пользователя страница 1

W4-IC Combination Smoke/ 

Carbon Monoxide (CO) Detector  

with Built-in Wireless Transmitter

INSTALLATION AND MAINTENANCE INSTRUCTIONS

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6583

www.systemsensor.com

BEFORE INSTALLATION

Please read this manual thoroughly along with the Application Guides for Sys-
tem Sensor Smoke (A05-1003) and CO Detectors (A05-1099), which provide 
detailed information on detector spacing, placement, zoning and special ap-
plications. Copies of these manuals are available at systemsensor.com.

IMPORTANT:  This detector must be tested and maintained regularly following 

NFPA 72/NFPA 720 requirements. 

GENERAL DESCRIPTION

The W4 series is a battery-operated, system-connected, combination carbon 
monoxide/smoke detector with a built-in wireless transmitter for use with 
iControl wireless control panel models. It will report maintenance, tamper and 
independent smoke alarm or CO alarm signals to a compatible wireless con-
trol panel. It has a speaker for vocal feedback, multi-criteria smoke detection, 
and integrated side LED windows that are viewable from 360 degrees when 
the detector is in an alarm condition.

FEATURES

Smoke Features

•  Multi-criteria smoke sensing using a combination of photoelectric, heat, 

flame flicker and carbon monoxide sensing.

•  Drift compensation and noise rejection algorithms.
•  Smoke test button.
•  360 degree, side viewable red LED smoke indication.

CO Features

•  10 year electrochemical CO sensor.
•  Sensor end-of-life notification. 
•  CO test button.
•  RealTest® functional gas entry test capable.
•  360 degree, side viewable blue LED CO indication.

Audible Annunciation

•  Local integral sounder.
•  Voice speaker provides supplemental instructions during alarm, installa-

tion and maintenance feedback.

Installation and Maintenance

•  Universal mounting base. 
•  Audible maintenance information including smoke sensitivity.

Other Features

•  Ships with 4 CR-123 lithium batteries. 
•  UL/ULC listed to standards 268 and 2075. 

SPECIFICATIONS 

Electrical Specifications

Voltage: 

3 volts DC

Battery Type:  

CR-123 lithium 

Battery Manufacturer: 

Duracell DL123A or Panasonic CR123A  

 

Use of a different battery may have a detrimental effect on device operation 

Number of Batteries: 

Sensitivity 

0.9 to 2.64/ft. (.27 to .80/m)

Audible Signal: 

85dBA

Physical Specifications

Diameter: 

5.95 inches (15.113 cm)

Height: 

2.03 inches (5.1562cm)

Weight: 

13.92oz (383 g)

Operating Temperature Range: 

0 - 38° C (32 - 100°F)

Storage Temperature Range: 

-10 - 70° C (14 - 158° F)

Operating Humidity Range: 

20-95% RH

This product is compatible with iControl Technicolor TCA203 control panels
*NFPA requires a UL listed sounder on the NAC circuit. 
Notice:  This manual shall be left with the owner/user of this equipment.

I56-5942-000

VISIBLE ANNUNCIATON

The W4 series detector has a multi-color top LED; Green, Red, and Amber. 
The LED is green for supervisory indication; it blinks during power on, reset, 
and during normal operation. The LED is amber to signal maintenance and 
trouble events. W4 utilizes the side LED windows to indicate alarm events; 
red for smoke and blue for CO. 

INSTALLATION GUIDELINES

Ceiling: Detector should be at least 12 inches (30 cm) from any wall.
Wall: Detector should be no closer than 6 inches (15 cm) from ceiling.

•  Do not install outdoors or in any environment that does not comply with 

the detector’s environmental specifications.

•  Install in accordance with NFPA 72 and 720 standards.

 

NFPA 72 and 

720 define standards for both commercial and residential installation of 
smoke and CO detectors. Local laws involving CO detection should also 
be considered.

•  If the installation can be interpreted as residential, consult the section 

of NFPA 720 that outlines residential applications.

 

Chapter 9.4.1.1, for 

example, states that carbon monoxide alarms or detectors shall be in-
stalled as follows:

•   Outside each separate dwelling unit sleeping area in the immediate 

vicinity of the bedroom.

•  On every level of a dwelling unit, including basements.
•   Consult NFPA 72, the local Authority Having Jurisdiction (AHJ), and/

or applicable codes for specific information regarding the spacing and 
placement of smoke detectors.

FIGURE 1: ALARM LOCATION DIAGRAM FOR RESIDENTIAL APPLICATION

 

LIVING

ROOM

BEDROOM

BEDROOM

BEDROOM

KITCHEN

TO
BR

CLOSED

DOOR

BASEMENT

GARAGE

CARBON MONOXIDE/SMOKE ALARM
LOCATION FOR MULTI-LEVEL RESIDENCE

  

S0295-01

Global 2.4 Ghz wireless use
ZigBee® Certified is a registered  
trademark of the Zigbee Alliance.

  

I56-5942-000 

 

 09-14

Содержание W4-IC

Страница 1: ...ifferent battery may have a detrimental effect on device operation Number of Batteries 4 Sensitivity 0 9 to 2 64 ft 27 to 80 m Audible Signal 85dBA Physical Specifications Diameter 5 95 inches 15 113 cm Height 2 03 inches 5 1562cm Weight 13 92oz 383 g Operating Temperature Range 0 38 C 32 100 F Storage Temperature Range 10 70 C 14 158 F Operating Humidity Range 20 95 RH This product is compatible ...

Страница 2: ... Zone screen If all of the sensors have not been configured the Modify screen appears for each sensor to let you review its details Change the details as needed or tap Next to cycle through all sensors The sensors are marked as configured MOUNTING Physically mount the smoke detector in the desired location NOTE NFPA 72 recommends the installation of detectors only after complet ing construction or...

Страница 3: ...and SDi SMOKESABRE 3 When the detector senses the presence of the smoke the detector will sound and illuminate per Table 2 and a smoke alarm signal will be sent to the control panel with a test indication 4 Verify the smoke alarm signal was received by the control panel FUNCTIONAL GAS TEST Solo C6 brand canned CO may be used to verify the detector s ability to sense CO by utilizing the RealTest fe...

Страница 4: ...sistance Also young children elderly and pets may be the first to be affected CO ALARM ACTIVATION Per UL standard 2075 the W4 series detector has been tested to the sensitivity limits defined in UL standard 2034 TABLE 4 CO ALARM THRESHOLDS Parts per Million ppm Detector Response Time Min 30 3ppm No alarm within 30 days 70 5ppm 60 240 150 5ppm 10 50 400 10ppm 4 15 FCC STATEMENT This device complies...

Отзывы: