manualshive.com logo in svg

Honeywell VR8215N, Руководство по установке, Страница: 9 / 12

Поделиться
Скачать
Honeywell VR8215N Скачать руководство пользователя страница 9

VR8215S,T SINGLE STAGE VR8215Q,N TWO STAGE DIRECT IGNITION GAS CONTROLS

9

69-2253—07

Two Stage

To convert from one gas to another:

1.

Turn off gas supply at the appliance service 
valve.

2.

Remove/unsnap plastic regulator cap. See 
Fig. 8.

3.

Remove regulator assembly by rotating 7/16 
Hex to left with supplied conversion tool. See 
Fig. 9.

4.

Remove spring from regulator assembly and 
replace with new spring.

5.

Reinstall regulator assembly back into valve 
housing, turning clockwise with 7/16 Hex 
conversion tool.

6.

Rotate regulator assembly 6 turns to reach a 
nominal high fire setting of approximately 
3.5 inches WC.

7.

Check the regulator setting using a manometer 
or by clocking the gas meter. See “Check and 
Adjust Gas Input and Burner Ignition” on page 5.

8.

Adjust high fire first by adjusting exterior 7/16 
Hex, After high fire has been set, adjust low fire 
utilizing interior 3/32 allen. See Fig. 8 and the 
Two Stage Regulator Adjustment process, below.

9.

Reinstall the plastic regulator cap.

10.

Mount conversion label on the gas control.

11.

Install the gas control and appliance according 
to the appliance manufacturer instructions.

Fig. 8. Top view of VR8215 two stage control with regulator cover removed.

C
HI

MV

ON

OFF

SET

SET

HI

LO SECOND

FIRST

HI

LO

INLET

OUTLET

PRESSURE REGULATOR

HIGH FIRE ADJUSTMENT

7/16 HEX

PRESSURE REGULATOR

LOW FIRE ADJUSTMENT

3/32 ALLEN

INLET

PRESSURE

TAP

REGULATOR CAP

COVER

ON/OFF

SWITCH

OUTLET 

PRESSURE 

TAP

ELECTRIC 

CONNECTION

MOLEX OR 

SPADE

M36774

Содержание VR8215N













Отзывы:

Нет отзывов