Honeywell TE529ELW Скачать руководство пользователя страница 6

10

9

READING THE KINETIC WAVE DISPLAY

The kinetic wave display shows the main unit (receiver)

signal reception strength.

MAXIMUM AND MINIMUM

TEMPERATURE & HUMIDITY

The maximum and minimum records of the indoor/outdoor

temperature and humidity will be automatically stored

in the memory of the main unit (receiver). Main unit

will display the minimum, maximum and the current reading

upon each press of 

MEM

 button. The unit will return to the

current temperature display in 15 seconds.

To clear the memory, press and hold 

MEM

 button and

stored readings will be erased.

TEMPERATURE TRENDS

The temperature trend indicator shows the trend of

temperatures collected at particular remote sight. There are

three trends will be shown: rising, steady, and falling.

COMFORT LEVEL INDICATORS

The comfort level indicators 

COM

WET

 or 

DRY

 will tell

you if the current environment is comfortable, too wet or

too dry. The comfort indicators will appear on the display

of the main unit when the following conditions are satisfied:

The unit is in searching mode.

Temperature readings

securely registered.

No signals.

˚

F

TREND

TREND

Arrow

indicator

Temperature

Trend

Steady

Falling

Rising

TREND

CHECKING REMOTE AND INDOOR TEMPERATURES

The wave icon on the main unit's display located near the

remote sensor reading line, indicates a good reception from

the remote sensor. If the temperature goes above or below the

temperature operating range stated in specifications, the

display will show dashes “       ”

WWVB RADIO CONTROLLED TIME

The NIST (National Institute of Standards and Technology)

radio station is located in Ft. Collins Colorado. It transmits

an exact time signal continuously throughout the continental

United States at 60 KHz frequency. The Weather Forecaster

can receive this WWVB signal through its internal antenna

from up to 2,000 miles away. Due to the nature of the Earth’s

ionosphere, reception can be limited during the daylight hours.

The radio controlled clock will search for an alternate station

that derives its signal from the NIST Atomic clock in Boulder,

Colorado.

* Make sure the main unit is positioned at 8 feet minimum

distance  from any interference source such as a TV,

computer monitor, microwave, etc. The successful reception

of the atomic time signal depends on the positioning and

location of the clock. Always place the main unit by the

window for better reception.

* Within concrete wall rooms such as basements or office

buildings, the received signal may be weakened.

Always place the unit near the window.

The WWVB tower icon on the main unit’s display will flash

indicating radio signal reception from the WWVB station.

If the tower icon is not fully lit, or if the time is not set

automatically, please consider the following:
* During night-time hours, atmospheric disturbances are

typically less severe and reception may improve.

A single daily reception is sufficient enough to keep

the accuracy reading within 1 second.

Содержание TE529ELW












Отзывы: