6
5
8
7
FRONT VIEW
A. TIME DISPLAY IN CLASSIC ANALOG FORMAT;
WEATHER DISPLAY IN DIGITAL FORMAT
Three-Channel Remote
Temperature and Humidity
Indoor Temperature &
Humidity
Comfort Level Indicator
Weather Forecast
B
B.
SNOOZE/LIGHT BUTTON
• Stops the clock alarm temporarily
• Activates a backlight feature for 5 seconds
C.
TEMP ALARM button
•
This product allows programming of a
HIGH
and
LOW
temperature alarms for all three remote
channels
D.
MEM button
•
Toggles between current, minimum, maximum
readings of the indoor and remote temperature &
humidity
•
Clears the temperature and humidity memory
E.
CHANNEL button
•
Recalls a different remote sensor reading – 1,2 or 3
•
Activates the remote channels auto-scan feature
F.
SET button
•
Enables the temperature programming in Celsius or
Fahrenheit
G.
CLOCK SET button
•
Enables clock’s manual programming
H.
DOWN ( ) BUTTON
•
Decreases the parameters in
SET
Mode
•
Activates the remote channels search
•
Disables the Temperature Alarm of all three remote
channels
I.
ALARM KNOB
•
Sets the clock’s alarm time
J.
BATTERY COMPARTMENT
•
Accommodates 2 (two) UM-3 or AA 1.5V alkaline
batteries
K.
ALARM ON/OFF SWITCH
•
Switches the clock alarm
ON
and
OFF
L.
REMOVABLE TABLE STAND
•
Keeps the unit in upright position
REMOTE SENSOR
FEATURES
• Remote temperature and humidity transmission to the
main unit via 433 MHz signal
• Case can be wall mounted using built-in hanger
• Selection of the temperature display in Celsius or
Fahrenheit
• Three Channel selection
• LCD displays temperature, humidity and channel
A. LED INDICATOR
• Flashes once when the remote sensor transmits a
reading to the main unit.
• Flashes twice when battery power is low.
B. BATTERY COMPARTMENT
• Holds two AA-size batteries
C. RESET
• Resets all previous settings
D. CHANNEL SWITCH
• Selects the desired channel -1, 2 or 3
E. WALL-MOUNT RECESSED HOLE
• Keeps the remote sensor on the wall
F.
°
C /
°
F SWITCH
• Selects the temperature display in Celsius or Fahrenheit
LEFT SIDE VIEW, REAR VIEW & RIGHT SIDE VIEW
RESET
˚C/˚F
CHANNEL
1 2 3
C
E
F
B
D
BEFORE YOU BEGIN
• We recommend using alkaline batteries for the remote
sensor and main unit when temperatures are above 32
°
F (0
°
C).
We recommend using lithium batteries for the remote
sensor when temperatures are below 32
°
F (0
°
C).
• Avoid using rechargeable batteries. (Rechargeable
batteries cannot maintain correct power requirements).
•
ALWAYS
install batteries in the
remote
sensor
before
the main unit.
• Insert batteries before first use, matching the polarity
in the battery compartment
• Press
RESET
after each battery change with a paper
clip or similar tool.
• Remove protective plastic screen from LCD display (if any).
• During an initial setup, place the main unit close to the
remote sensor.
• After reception is established (the remote temperature
and humidity will appear on the main unit’s display),
position the remote sensor and the main unit within the
effective transmission range of 200 feet (60 meters).
• The remote sensor can be placed
indoors or outdoors,
depending on the area where the temperature and
humidity are intended to be measured
. If you intend
measuring outdoor elements, place remote sensor outdoors
• The main unit must be placed indoors.
NOTE:
1. Avoid pressing any buttons on the main unit
before the
remote readings are displayed.
2. The effective operating range may be influenced by the
surrounding building materials and how the receiver
and transmitter are positioned.
3. Place the remote sensor so that it faces the main
unit (receiver), minimizing obstructions such as doors,
walls, and furniture.
4. Though the remote sensors are weather-resistant, they
should be placed away from direct sunlight, rain or snow.
The best suggested location for the remote sensor for
outdoors is under the eave on the north side of the building.
A
THERMO – HYGRO SENSOR
1
Alarm
Seconds
Hours
F
G
J
L
H
K
I
E
D
C
Minutes
