Honeywell TB3 Series Скачать руководство пользователя страница 1

Страница: 1 / 24

INSTALLATION INSTRUCTIONS

® U.S. Registered Trademark

31-00576-01

TB3 Series Communicating Thermostats

FOR 2-PIPE AND 4-PIPE FAN COIL UNITS

APPLICATION

TB3 Series Fan Coil Thermostats are used in individual

rooms or zones in buildings. It is designed for two and

four-pipe fan coil units. TB3 Series has one universal

input as an external sensor (NTC10k) or open/close

contact input, three relay fan outputs, two relay valve

outputs (TB3140), two analog valve outputs (TB3240),

and one EIA-485 (BACnet MS/TP). It controls the fan

coil unit depending on the internal room sensor or

external return sensor temperature.

The following NTC10K sensor and flange are

recommended: VF10-3B65NW and LF-MF

CAUTION

• The authorized service must do assembly,

maintenance, diagnostic, and repair. The device's

power supply is 220 VAC (TB3140) and 24V

AC/DC (TB3240), and it has no internal fuse.

• External protection with max C10A (TB3140)

and C5A (TB3240) circuit breakers are required

in all cases.

• Disconnect the power supply before separating

the front plate.

INSTALLATION

• Read these instructions carefully. Failure to follow

them could damage the product or cause a

hazardous condition.

• Check the ratings in the instructions and the product

to ensure the product is suitable for your application.

The Installer must be a trained, experienced service

technician.

• After installation is complete, check out product

operation as provided in these instructions.

• All wiring must agree with applicable codes,

ordinances, and regulations, as specified in

installation wiring diagrams.

• TB3 Series thermostat safety rules are in accordance

with the latest technological developments designed

and manufactured. Adhere to the safety precautions

to avoid injury and property damage.

CAUTION

Power off the supply at circuit breaker or fuse

before installation to avoid fire, shock, or death!

Содержание TB3 Series

























Результаты поиска

Содержание TB3 Series

Отзывы:

Honeywell TB3 Series, Руководство по установке, Страница: 1 / 24

Результаты поиска

Содержание TB3 Series

Отзывы: