manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 325 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 325

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Program Mode

Chapter 5

page 303

2. The following display appears.  This is your list of cam channels. Now you can select

and set a channel.  (If you named your cam channels in Initialization mode, those names
will appear, instead of channel 1, channel 2, etc.)

NOTICE

We are illustrating 16 cams.  Depending upon the way that  your SmartPAC 2 has been
configured (with ProCam 8 cams or with ProCam 16 cams), your display may vary.  We are
showing the ProCamPAC 16 module.  Also, if you had named the cam channels in
Initialization mode (Chapter 4), the channel number will be replaced with the name.

F1

F2

F3

F4

F5

F6

F7

F8

Figure 5 - 27.  Cam Program Menu

Go to the page indicated for instructions on performing the following operations:

View Global Cams, next section

View Cam Summary, page 305

Make an ON/OFF Setting for a Channel, page 305
Multiple ON/OFFs for Cam Channels, page 307

Selecting a Channel and Making a Timed Output Setting, page 309

Selecting a Channel and Making an Auto Advance Setting, page 311
Setting DSV ON Channel Timing, page 312

Set Other Channels for the Tool, page 313

Delete Channel Settings, page 313

For HELP press the HELP key located at the center of the cursor (arrow) keys.

NOTICE

You can set multiple ON/OFFs for your cams.  See page 307.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов