Honeywell SmartPAC 2 Скачать руководство пользователя страница 333 | Manualshive

Страница: 333 / 522

Honeywell SmartPAC 2 Скачать руководство пользователя страница 333

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Program Mode

Chapter 5

page 311

For applications requiring more than 500 milliseconds

If you have an application where more than a 500-millisecond "on-time" is required, use one
of the batch counters instead of programming a timed output setting (as explained above).
To accomplish this, set the "batch count" to a value of 1 and the "counter angle" accordingly.
Next, set the cam's "on-time" as the batch's "pulse time.” For more assistance in
programming batch counters, see "Setting Counter Mode" earlier in this chapter.

NOTICE

SmartPAC 2 saves your settings automatically. You do not have to press any key or issue
any command to save settings.

Selecting a Channel and Making an Auto Advance Setting

NOTICE

MAXIMUM NUMBER OF AUTO ADVANCE CHANNELS PER TOOL

Each tool can have up to two Auto Advance cam channels.

You can make an auto advance setting whenever you want SmartPAC 2 to automatically
compensate the cam timing for changes that occur in press speed. A good example of this is
top stop because it ensures the same top stop position, regardless of varying press speeds.
You can also use "auto" settings for feed, pilot release, lube, etc.

You can set up a maximum

of two channels as "auto.”

NOTICE

You can program up to two "auto" output settings in Program mode. The first advance
constant set in Initialization mode affects the

lowest-numbered

channel that you set as

"auto" in Program mode, and likewise the next

numerically higher

channel number uses the

second "advance constant" setting. In other words, if channel 3 and channel 5 are
programmed using Auto Advance, channel 3 will use the first advance constant, and channel
5 will use the second. See "Auto Advance" in Chapter 4 for more information about advance
constants.

To make an auto advance setting for a channel:

1. Select the channel you want to set from the list of cam channels. You will then see the

display for choosing an on/off output, timed output, or auto advance settings.

2. Select "Program auto advance." You see a display showing the tool number, channel

number, and name of the channel you are setting shown at the top of the screen.

3. Set the "on angle" and "off angle" using the cursor keys. Notice that an arc will move

around the circle diagram as you set the "auto on" and the "auto off" angles. These
settings are also shown numerically in the box on the display along with the dwell. See
"Cursor keys" under "Using the keyboard" in Chapter 3 if necessary.

«
...
331
332
333
334
335
...
»

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов