manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 227 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 227

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Initialization Mode

Chapter 4

page 205

POSITION SENSOR

(INITIALIZATION – POSITION SENSOR)

NOTICE

DISABLE POSITION SENSOR ON SMARTPAC 2/WPC INTEGRATION

An overrun limit sensor is required for SmartPAC 2 with WPC integration; you cannot use a
position sensor.  Be sure to disable Position Sensor mode, as instructed below.

This choice enables you to set a number of different settings. When you select the
POSITION SENSOR choice in the main Initialization menu, a display appears similar to that
in the next figure.   You should disable the position sensor mode with a SmartPAC 2 – WPC
integration system.  To make this and other settings see the following sections:

•

 

POSITION SENSOR MODE:  Should be disabled.  See next section.

•

 

RESOLVER MOTION MODE, page 206

•

 

TOOL NUMBER MODE, page 206

•

 

COUNTER SETUP MODE, page 208

Figure 4 - 4.  Position Sensor Display

Position Sensor Mode

(INITIALIZATION – POSITION SENSOR)

Follow the instructions below to disable position sensor mode.  To operate SmartPAC 2 with
WPC, this must be disabled.

1. This entry should read “DISABLED,” which is the factory setting.  If it does not read

“disabled,” press ENTER so that it does say “disabled.”

2. Press RESET when done.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов