WIRING
NOTE:
All wiring must conform to applicable local
codes, ordinances, and regulations.
1. Install module wiring in accordance with the job draw-
ings and appropriate wiring diagrams.
2. All wiring to the IDP-Monitor-10 is done via terminal
blocks. In order to properly make electrical connec-
tions strip approximately
1
⁄
4
˝ of insulation from the
end of wire, sliding the bare end of the wire under the
clamping plate screw.
3. Set the address on the modules per the job drawing. Use
the rotary code switches to set the address of the first
module (between 01 and 90).
In Class B operation, the remaining modules are automati
cally assigned to the next nine higher addresses. For
example, if the base address switch is set to 28, the next
nine modules will be addressed to 29, 30, 31, 32, 33, 34,
35, 36, and 37.
The module is shipped in Class B position, remove
shunt for Class A.
When operating in Class A, alternate
modules are paired together (+0/+1, +2/+3, +4/+5, +6/+7,
+8/+9), resulting in a total of five modules. For example,
if the base address switch is set to 28, then 30, 32, 34
and 36 will be automatically assigned to the modules
while 29, 31, 33, 35 and 37 are available to be used for
other modules on the SLC. For Class A and B operation,
DO NOT set the lowest address above 90, as the other
modules will be assigned to nonexistent addresses.
NOTE:
The IDP-Monitor-10 must have power cycled for
shunt changes to take effect.
K200-14-00
3
I56-2731-003
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful in-
terference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
4. A shunt is provided to disable a maximum of two un-
used modules in Class B operation and one unused
module in Class A operation. Modules are disabled
from the highest address and work downward. If two
modules are disabled, the lowest eight addresses will
be functional, while the highest two will be disabled.
For example, in Class B operation, if the shunt for
Address Disable is placed on “two” and the base switch
is set to 28, the modules will be assigned to 28, 29, 30,
31, 32, 33, 34 and 35 while disabling the highest two
positions.
5. A communications loss feature is available on some
panels. Upon a communication loss, due to a micro-
processor failure at the control unit, the IDP-Monitor-
10 will send a signal to the control unit to activate the
notification device circuits upon initiating of an alarm
on the IDP-Monitor-10. A single shunt is used to en-
able (shunt on) or disable (shunt off) this feature for all
modules on the board.
NOTE:
Place unused shunts on single pin to store on
board for future use.
WIRING NOTES
• Power-limited circuits must employ type FPL, FPLR,
or FPLP cable as required by Article 760 of the NEC.
PROGRAMMING
The modules are programmed as devices in each system
according to the programming instructions in the appro-
priate FACP manual.
firealarmresources.com
